Electroformation of Giant Unilamellar Vesicles from Damp Lipid Films with a Focus on Vesicles with High Cholesterol Content

Ivan Mardešić,Zvonimir Boban,Marija Raguz

DOI: https://doi.org/10.3390/membranes14040079

IF: 4.562

2024-03-28

Membranes

Abstract:Giant unilamellar vesicles (GUVs) are membrane models used to study membrane properties. Electroformation is one of the methods used to produce GUVs. During electroformation protocol, dry lipid film is formed. The drying of the lipid film induces the cholesterol (Chol) demixing artifact, in which Chol forms anhydrous crystals which do not participate in the formation of vesicles. This leads to a lower Chol concentration in the vesicle bilayers compared to the Chol concentration in the initial lipid solution. To address this problem, we propose a novel electroformation protocol that includes rapid solvent exchange (RSE), plasma cleaning, and spin-coating methods to produce GUVs. We tested the protocol, focusing on vesicles with a high Chol content using different spin-coating durations and vesicle type deposition. Additionally, we compared the novel protocol using completely dry lipid film. The optimal spin-coating duration for vesicles created from the phosphatidylcholine/Chol mixture was 30 s. Multilamellar vesicles (MLVs), large unilamellar vesicles (LUVs) obtained by the extrusion of MLVs through 100 nm membrane pores and LUVs obtained by extrusion of previously obtained LUVs through 50 nm membrane pores, were deposited on an electrode for 1.5/1 Chol/phosphatidylcholine (POPC) lipid mixture, and the results were compared. Electroformation using all three deposited vesicle types resulted in a high GUV yield, but the deposition of LUVs obtained by the extrusion of MLVs through 100 nm membrane pores provided the most reproducible results. Using the deposition of these LUVs, we produced high yield GUVs for six different Chol concentrations (from 0% to 71.4%). Using a protocol that included dry lipid film GUVs resulted in lower yields and induced the Chol demixing artifact, proving that the lipid film should never be subjected to drying when the Chol content is high.

engineering, chemical,materials science, multidisciplinary,polymer science,chemistry, physical

What problem does this paper attempt to address?

The main aim of this paper is to address the issue encountered when using the electroformation method to prepare Giant Unilamellar Vesicles (GUVs) with high concentrations of Cholesterol (Chol), specifically that Chol forms anhydrous crystals during the drying process and does not participate in vesicle formation, resulting in a lower concentration of Chol in the final GUVs than in the initial lipid solution.

To solve this problem, the researchers proposed an improved electroformation protocol that includes Rapid Solvent Exchange (RSE), plasma cleaning, and spin-coating techniques to produce GUVs. Specifically, this method avoids the step of drying the lipid film and instead uses spin-coating to deposit Multilamellar Vesicles (MLVs) pre-formed by the RSE method onto plasma-treated electrodes to form a wet lipid film. Subsequently, these lipid films form GUVs under the influence of osmotic pressure and an alternating electric field.

The study also tested the effects of different spin-coating times, different types of vesicles (MLVs and two different sizes of Large Unilamellar Vesicles, LUVs) on deposition, and different Chol concentrations on GUV formation. The results showed that a spin-coating time of 30 seconds was the optimal condition; using LUVs obtained by extrusion through a 100 nm pore size filter for deposition yielded the most reproducible results; and the optimized protocol successfully produced GUVs with six different Chol concentrations (ranging from 0% to 71.4%), demonstrating that this method can significantly reduce Chol phase separation and increase GUV yield.