Abstract:Fillers have been widely used in natural rubber (NR) products. They are introduced to serve as a strategy for modifying the final properties of NR vulcanizates. Silica and calcium carbonate (CaCO3) are among the fillers of choice when the color of the products is concerned. In this case, a special focus was to compare the vulcanizing efficiency of NR filled with two different filler types, namely nano-sized silica and micrometer-sized CaCO3. This study focused on the effects of the loading level (10–50 parts per hundred parts of rubber, phr) on the final properties and structural changes of NR composites. The results indicated that increased filler loading led to higher curing torques and stiffness of the rubber composites irrespective of the type of filler used. The better filler dispersion was achieved in composites filled with CaCO3 which is responsible for less polarity of CaCO3 compared to silica. Good filler distribution enhanced filler–matrix interactions, improving swelling resistance and total crosslink density, and delaying stress relaxation. The modulus and tensile strength of both composites also improved over the content of fillers. The CaCO3-filled composites reached their maximum tensile strength at 40 phr, exceeding, by roughly 88%, the strength of an unfilled sample. Conversely, the maximum tensile strength of silica-filled NR was at 20 phr and was only slightly higher than that of its unfilled counterpart. This discrepancy was ascribed to the stronger rubber–filler interactions in cases with CaCO3 filler. Effective rubber–filler interactions improved strain-induced crystallization, increasing crystallinity during stretching and reducing the strain at which crystallization begins. In contrast, large silica aggregates with poor dispersion reduced the overall crosslink density, and degraded the thermomechanical properties, tensile properties, and strain-induced crystallization ability of the NR. The results clearly indicate that CaCO3 should be favored over silica as a filler in the production of some rubber products where high performance was not the main characteristic.

Physical and mechanical properties of natural rubber latex film (Rubber Dam) products with filler nanocrystal cellulose from peanut shell (Arachis hypogea L.) and synthetic dyes

Enhanced Mechanical Properties of Natural Rubber by Block Copolymer-Based Porous Carbon Fibers

Natural Fiber Fillers and their Influence on the Properties of Rubber

Extraction of Cellulose Nanocrystals and Nanofibers from Rubber Leaves and Their Impacts on Natural Rubber Properties

Composites of resorcinol and hexamethylenetetramine modified nanocellulose whiskers as potential biofiller in natural rubber latex: synthesis, characterization and property evaluation

Cure Characteristics, Mechanical, Thermal, And Coloring Properties Of Natural Rubber/Dye-Loaded Shell Powder Composites

Utilization of peanut shell powder as a novel filler in natural rubber

Comparative Investigation of Nano-Sized Silica and Micrometer-Sized Calcium Carbonate on Structure and Properties of Natural Rubber Composites

Linear Rheology of Natural Rubber Compounds Filled with Silica, Short Nylon Fiber or Both

Surface Modified Nanocellulose and Its Reinforcement in Natural Rubber Matrix Nanocomposites: A Review

Tailoring natural rubber composites via surface-modified nanocellulose whiskers with sodium isopropyl xanthate: characterization and performance analysis

Study on the Effect of Halloysite Nanotubes on the Mechanical Properties and Swelling Resistance of Ethylene-Propylene Diene Monomer (EPDM)/Nitrile Butadiene Rubber (NBR) Blend Nanocomposites

Preparation of Deproteinized Natural Rubber Latex and Properties of Films Formed by Itself and Several Adhesive Polymer Blends

EFFECT OF CELLULOSE FIBER SURFACE TREATMENT TO REPLACE CARBON BLACK IN NATURAL RUBBER HYBRID COMPOSITES

The Effect of High Loaded Multiwall Carbon Nanotubes in Natural Rubber and Their Nonlinear Material Constants

Achieving ultra-tear resistant high-performance natural rubber nanocomposite via bio-inspired lignocellulosic compatibilization

Effect of complex of resorcinol and hexamethylenetetramine modified halloysite nanotubes (RH-HNTs) on the mechanical and swelling characteristics of NR/EPDM nanocomposites

Effect of Poly (Butyl Acrylate) and Poly (Ethylene Oxide) Modified Sago Starch on Natural Rubber Latex Films Physical Properties

A relationship between cross-link concentration and physical properties in natural rubber latex films at different calcium carbonate loadings

Natural Rubber Nanocomposites: A Review

Application of Tamarind Shell as a Green Additive in Natural Rubber