Abstract:Fused deposition modeling (FDM) printed polymers are rarely used as a structural material due to anisotropic and low mechanical properties compared with conventional composites. In recent years, greater need has been expressed for recycling of materials, such as recyclable FDM, at the end of service life to reduce environmental pollution and manufacture cost. However, how the amount of resin uptake in the skin and skin/core interphase affects the bending and shear performance of the sandwich composites when replacing the low strength and ductile core (conventional core) with a high strength and brittle core (FDM printed PLA (polylactic acid) core) still remains unclear. A new manufacturing routine is needed to improve the incorporation of FDM printed polymers in composite structures. In this work, FDM printed PLA was used as core material and sandwiched between two unidirectional glass fiber reinforced polymer (GFRP) skins to form a sandwich composite by compression-molding (CM) process, which provides a good manufacturing strategy for skin/core interphase modification. The significance of the CM process is proved by investigating the effect of resin uptake on bending and in-plane/out-of-plane shear performances. Current first order shear deformation (FSDT) theory lacks a direct connection between the in-plane shear stress and out-of-shear stress in the core region of sandwich composites. With the help of DIC, a connection between the in-plane shear and the out-of-plane shear strain was built and in-plane shear properties can acquire through out-of-plane shear properties, hence reducing the redundancy of sample preparation or the need for simulation. A significant improvement was found compared with the optimized resin uptake (Optimized resin uptake range: 20.43%–22.86 wt%) 3D-printed PLA core sandwich composite and lowest performance sandwich composite (Improvement: in-plane shear strength (∼34%)/modulus (∼29%), out-of-plane shear strength (∼25%)/modulus (∼31%), specific peak bending load (∼19%)). Compared with balsa core sandwich composites, the 3D-printed cores are suitable for use in composite sandwich structures in many applications with a satisfactory strength-to-weight ratio.

Theoretical and experimental investigation of sandwich panels with 3D printed cores with GFRP composite and aluminum face sheets under 3-point bending

Initial performance assessment of 3D printed thin walled structures for spacecraft applications

Experimental and Theoretical Study of Sandwich Panels with Steel Facesheets and Gfrp Core

Exploring bending behavior of curved sandwich panels with three-dimensional printed, functionally graded cores

Three-point bending behaviors of the foam-filled CFRP X-core sandwich panel: Experimental investigation and analytical modelling

Experimental and Analytical Study on the Mechanical Behavior of Stitched Sandwich Composite Panel with a Foam Core

Impact of Infill Density and Glass Fiber Reinforcement on the Compressive and Bending Strength of Acrylonitrile Butadiene 3D‐Printed Corrugated Sandwich Panels

Experimental analysis of the flexural and compressive properties of carbon fiber reinforced sandwich panels with M-shaped core

Study on Flexural Behavior of Glass Fiber Reinforced Plastic Sandwich Composites Using Liquid Thermoplastic Resin

Mechanical performances of metal-polymer sandwich structures with 3D-printed lattice cores subjected to bending load

The flexural and compressive properties of sandwich composites with different 3D-printed core structures

Bending and shear improvements in 3D-printed core sandwich composites through modification of resin uptake in the skin/core interphase region

Experimental, numerical and optimization investigation of sandwich structures with 3D-printed sacrificial core under explosive loading

Mechanical Properties of Sandwiched Construction with Composite and Hybrid Core Structure

Mechanical Behavior of Sandwich Panels with Hollow Al-Si Tubes Core Construction

Exploring flexural behavior of additively manufactured sandwich beams with bioinspired functionally graded cores

Shear and Bending Performance of Carbon Fiber Composite Sandwich Panels with Pyramidal Truss Cores

Experimental Study of Manufacture and Mechanical Behavior of Sandwich Structure with Composite Foldcores

Experimental and Numerical Studies on Core Stiffened Sandwich Composite Panel

Experimental investigation on 3D printed lightweight sandwich structures for energy absorption aerospace applications

Mechanical characterization of a 3D printed lattice core sandwich structure