Abstract:Although there has been extensive development and exploration of small-scale robots, the technological challenges associated with their complicated and high-cost fabrication processes remain unresolved. Here, we report a one-step, bi-material, high-resolution three-dimensional (3D) printing method for the fabrication of multi-stimuli-responsive microactuators. This method exploits a two-phase femtoliter ink meniscus formed on a double-barreled theta micropipette to continuously print a freestanding bilayer microstructure, which undergoes an asymmetric volume change upon the adsorption or desorption of water. We show that the 3D-printed bilayer microstructures exhibit reversible, reproducible actuation in ambient humidity or under illumination with infrared light. Our 3D printing approach can assemble bilayer segments for programming microscale actuation, as demonstrated by proof-of-concept experiments. We expect that this method will serve as the basis for flexible, programmable, one-step routes for the assembly of small-scale intelligent actuators.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsami.1c12574.Quantitative analysis of energy-dispersive X-ray spectroscopy images; atomic force microscopy images of the bilayer structure; effects of polystyrene (PS) ink content on the layer thickness; FE-SEM image of a glass double-barreled theta pipette; the procedure of time-resolved bending angle measurement; the response times for bending actuations; cyclic stability of the bending angle of a bilayer structure over 4000 s; comparison of our actuators to other humidity-responsive actuators; the setup for humidity control (PDF)Movie S1: Process for three-dimensional printing of a bilayer structure (MP4)Movie S2: Two-segment bilayer actuation under the stimulus of humidity (MP4)Movie S3: Three-segment bilayer actuation under the stimulus of humidity (MP4)Movie S4: Four-segment bilayer actuation under the stimulus of humidity (MP4)Movie S5: The process of grasping a silica particle using a gripper under the stimulus of humidity (MP4)This article has not yet been cited by other publications.

Controllable Multimodal Actuation in Fully Printed Ultrathin Micro-Patterned Electrochemical Actuators

Printed Paper Actuator

Printed Paper Actuator: A Low-cost Reversible Actuation and Sensing Method for Shape Changing Interfaces.

Thickness-dependent response of aerosol-jet-printed ultrathin high-aspect-ratio electrochemical microactuators

One-Step, Continuous Three-Dimensional Printing of Multi-Stimuli-Responsive Bilayer Microactuators via a Double-Barreled Theta Pipette

Materials for electronically controllable microactuators

4D Multimaterial Printing of Soft Actuators with Spatial and Temporal Control

Giant-Amplitude, High-Work Density Microactuators with Phase Transition Activated Nanolayer Bimorphs

Showcasing Printed Paper Actuator

Stimuli-Responsive Actuator Fabricated by Dynamic Asymmetric Femtosecond Bessel Beam for In Situ Particle and Cell Manipulation.

Dual‐Material Aerosol Jet Printing of Magneto‐Responsive Polymers with In‐Process Tailorable Composition for Small‐Scale Soft Robotics

Magnetic soft micromachines made of linked microactuator networks

Micron-sized Liquid Crystalline Elastomer Actuators

Fully 3D‐Printed Miniature Soft Hydraulic Actuators with Shape Memory Effect for Morphing and Manipulation

Multimaterial Printing of Liquid Crystal Elastomers with Integrated Stretchable Electronics

Design and fabrication of an electrothermal MEMS micro-actuator with 3D printing technology

Large-Displacement Micro Pneumatic Actuators Based on Corrugated Parylene Film

Spray-Printing and Spin Methods to Fabricate Multilayered Dielectric Elastomer Actuators Embedded with Liquid Metal Electrodes

Micrometer-sized electrically programmable shape-memory actuators for low-power microrobotics

An airbrush 3D printer: Additive manufacturing of relaxor ferroelectric actuators

Reprogrammable Magnetic Soft Actuators with Microfluidic Functional Modules via Pixel‐Assembly