Abstract:For laser-melting deposition (LMD), a computational fluid dynamics (CFD) model was developed using the volume of fluid and discrete element modeling techniques. A method was developed to track the flow behavior, flow pattern, and driving forces of liquid flow. The developed model was compared with experimental results in the case of AISI 304 stainless steel single-track depositions on AISI 304 stainless steel substrate. A close correlation was found between experiments and modeling, with a deviation of 1–3%. It was found that the LMD involves the simultaneous addition of powder particles that absorb a significant amount of laser energy to transform their phase from solid to liquid, resulting in conduction-mode melt flow. The bubbles within the melt pool float at a specific velocity and escape from the melt pool throughout the deposition process. The pores are generated if the solid front hits the bubble before escaping the melt pool. Based on the simulations, it was discovered that the deposited layer’s counters took the longest time to solidify compared to the overall deposition. The bubbles strived to leave through the contours in an excess quantity, but became stuck during solidification, resulting in a large degree of porosity near the contours. The stream traces showed that the melt flow adopted a clockwise vortex in front of the laser beam and an anti-clockwise vortex behind the laser beam. The difference in the surface tension between the two ends of the melt pool induces “thermocapillary or Benard–Marangoni convection” force, which is insignificant compared to the selective laser melting process. After layer deposition, the melt region, mushy zone, and solidified region were identified. When the laser beam irradiates the substrate and powder particles are added simultaneously, the melt adopts a backwards flow due to the recoil pressure and thermocapillary or Benard–Marangoni convection effect, resulting in a negative mass flow rate. This study provides an in-depth understanding of melt pool dynamics and flow pattern in the case of LMD additive manufacturing technique.

In suit monitoring of solidification mode, porosity and clad height during laser metal deposition of AISI 316 stainless steel

Investigation on coaxial visual characteristics of molten pool in laser-based directed energy deposition of AISI 316L steel

Pore defects and corrosion behavior of AISI 316L stainless steel fabricated by laser directed energy deposition under closed-loop control

Temperature Field Simulation and Experimental Analysis of Laser Cladding 45 Steel.

Prediction of powder bed thickness by spatter detection from coaxial optical images in selective laser melting of 316L stainless steel

Influence of pulsed laser scanning patterns on microstructural evolution and mechanical properties of Inconel 718 in direct laser deposition

Crack Detection during Laser Metal Deposition by Infrared Monochrome Pyrometer

Predominant Solidification Modes of 316 Austenitic Stainless Steel Coatings Deposited by Laser Cladding on 304 Stainless Steel Substrates

Solidification behavior and texture of 316L austenitic stainless steel by laser wire directed energy deposition

Solidification microstructure and residual stress correlations in direct energy deposited type 316L stainless steel

In-situ Monitoring and Defect Detection of Selective Laser Melting Process and Impact of Process Parameters on the Quality of Fabricated SS 316L

Anisotropy Evaluation and Defect Detection on Laser Power Bed Fusion 316L Stainless Steel

Evolutionary Mechanism of Solidification Behavior in the Melt Pool during Disk Laser Cladding with 316L Alloy

Defect recognition in Ti-6Al-4V fabrication by in situ monitoring of directed energy deposition using a laser beam

Statistical modelling and optimization of clad characteristics in laser metal deposition of austenitic stainless steel

Mesoscopic Computational Fluid Dynamics Modelling for the Laser-Melting Deposition of AISI 304 Stainless Steel Single Tracks with Experimental Correlation: A Novel Study

Laser Directed Energy Deposition of Bulk 316L Stainless Steel

Monitoring of laser metal deposition height by means of coaxial laser triangulation

Prediction of Primary Dendrite Arm Spacing of the Inconel 718 Deposition Layer by Laser Cladding Based on a Multi-Scale Simulation

Predictions of in-situ melt pool geometric signatures via machine learning techniques for laser metal deposition

Machine Vision-based in Situ Monitoring of Laser Cladding Molten Pool Features