Abstract:Lithium–sulfur (Li–S) batteries are severely hindered by the low sulfur utilization and short cycling life, especially at high rates. One of the effective solutions to address these problems is to improve the sulfiphilicity of lithium polysulfides (LiPSs) and the lithiophilicity of the lithium anode. However, it is a great challenge to simultaneously optimize both aspects. Herein, by incorporating the merits of strong absorbability and high conductivity of SnS with good catalytic capability of ZnS, a ZnS-SnS heterojunction coated with a polydopamine-derived N-doped carbon shell (denoted as ) with uniform cubic morphology was obtained and compared with the ZnS-SnS2@NC heterostructure and its single-component counterparts ( and SnS2@NC). Theoretical calculations, ex situ XANES, and in situ Raman spectrum were utilized to elucidate rapid anchoring-diffusion-transformation of LiPSs, inhibition of the shuttling effect, and improvement of the sulfur electrochemistry of bimetal ZnS-SnS heterostructure at the molecular level. When applied as a modification layer coated on the separator, the cell with optimized lithiophilicity and sulfiphilicity enables desirable sulfur electrochemistry, including high reversibility of 1149 mAh g–1 for 300 cycles at 0.2 C, high rate performance of 661 mAh g–1 at 10 C, and long cycle life with a low fading rate of 0.0126% each cycle after 2000 cycles at 4 C. Furthermore, a favorable areal capacity of 8.27 mAh cm–2 is maintained under high sulfur mass loading of 10.3 mg cm–2. This work furnishes a feasible scheme to the rational design of bimetal sulfides heterostructures and boosts the development of other electrochemical applications.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsnano.1c00270?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsnano.1c00270</a>.Additional experimental sections (materials synthesis, characterizations, and DFT calculations); SEM, TEM, XRD, TG, XPS, BET, and XANES characterizations of the samples; CV curves; discharge–charge profiles and cycle performance of various electrodes; in situ Raman tests; optimized geometries of LiPSs; Tables S1–S6: Li+ diffusion rates, EIS fitting, and comparisons of electrochemical performance (<a class="ext-link" href="/doi/suppl/10.1021/acsnano.1c00270/suppl_file/nn1c00270_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Engineering Catalytic CoSe–ZnSe Heterojunctions Anchored on Graphene Aerogels for Bidirectional Sulfur Conversion Reactions

Design of ZnSe-CoSe heterostructure decorated in hollow N-doped carbon nanocage with generous adsorption and catalysis sites for the reversibly fast kinetics of polysulfide conversion

A Rational Design of a CoS2-CoSe2 Heterostructure for the Catalytic Conversion of Polysulfides in Lithium-Sulfur Batteries

Anion‐Doped Cobalt Selenide with Porous Architecture for High‐Rate and Flexible Lithium–Sulfur Batteries

Core–shell zeolite imidazole framework-derived ZnSe@CoSe2/C heterostructure enabling robust polysulfide adsorption and rapid Li+ diffusion in high-rate and high-loading lithium–sulfur batteries

A High‐Efficiency CoSe Electrocatalyst with Hierarchical Porous Polyhedron Nanoarchitecture for Accelerating Polysulfides Conversion in Li–S Batteries

Built-in Electric Field Within CoSe2-FeSe2 Heterostructure for Enhanced Sulfur Reduction Reaction in Li-S Batteries

Self-Assembled 3D CoSe-based Sulfur Host Enables High-Efficient and Durable Electrocatalytic Conversion of Polysulfides for Flexible Lithium-Sulfur Batteries

Co/CoSe Junctions Enable Efficient and Durable Electrocatalytic Conversion of Polysulfides for High‐Performance Li–S Batteries

Mott Schottky heterojunction Co/CoSe2 electrocatalyst: Achieved rapid conversion of polysulfides and Li2S deposition dissolution via built-in electric field interface effect

Catalytic Boosting Bidirectional Polysulfide Redox using Co 0.85 Se/C Hollow Structure for High‐Performance Lithium‐Sulfur Batteries

Bidirectional tandem catalysis coupled with interface engineering and Se vacancies for accelerating the polysulfide conversion

MOF-Derived Bifunctional Co 0.85 Se Nanoparticles Embedded in N-Doped Carbon Nanosheet Arrays as Efficient Sulfur Hosts for Lithium–Sulfur Batteries

Deciphering the electrocatalysis essence of cobalt diselenide in lithium-sulfur electrochemistry from crystal-phase engineering

Co‐recrystallization Induced Self‐catalytic Li2S Cathode Fully Interfaced with Sulfide Catalyst Toward a High‐performance Lithium‐free Sulfur Battery

Bidirectional Catalysts for Liquid–Solid Redox Conversion in Lithium–Sulfur Batteries

Nitrogen-Doped CoSe2 As a Bifunctional Catalyst for High Areal Capacity and Lean Electrolyte of Li–S Battery

Synergistic Effect of Zn–Co Bimetallic Selenide Composites for Lithium–Sulfur Battery

2D Cu 2− x Se@graphene multifunctional interlayer boosting polysulfide rapid conversion and uniform Li 2 S nucleation for high performance Li–S batteries

ZnS-SnS@NC Heterostructure as Robust Lithiophilicity and Sulfiphilicity Mediator toward High-Rate and Long-Life Lithium–Sulfur Batteries

Accelerating sulfur conversion kinetics via CoS2–MgS heterostructure for lithium sulfur batteries