Abstract:The present study investigates the adoption of laser surface treatments to improve the bonding strength of dissimilar material hybrid structures made by the thermomechanical joining process. Aluminium AA7075 alloy was joined to Polyether-ether-ketone through a friction-assisted joining process. For the surface treatment, a two-step laser treatment was adopted. The latter consists of a first phase, called laser texturing, where a deep square grid texture is obtained by adopting high pulse energy and repetitions, followed by a further laser treatment, called cleaning, carried out with lower energy content, and applied over the overall adhesion surface. Two textures characterised by different grid sizes (200 and 300 µm) were realised. As received, uncleaned, and only cleaned samples were adopted as reference treatments. The results indicated that laser cleaning performed after laser texturing enabled a significant improvement of adhesion irrespective of the previous laser texturing strategy. This was also confirmed by the higher amount of polymer trapped within the laser-texturized paths. The only laser cleaning treatment enabled the successful joining of the substrates with an average shear strength of 12 MPa. On the other hand, when texturing with a hatch distance of 200 μm, laser cleaning performed after texturing increased the shear strength from 18.4 MPa to 25.2 MPa corresponding to an increase of 37%. The increased adhesion between the PEEK and the aluminium was also indicated by the change in the failure mode of the joints. The texturized samples with a hatch distance of 200 μm failed by pull-out; when the laser cleaning was performed on these samples, they failed by cohesive failure.

Processing understanding, mechanical durability and hygrothermal stability of PC/AA6061 hybrid joints produced via injection overmolding

Mechanical property and structure of polycarbonate /aluminum alloy hybrid prepared by ultrasound-assisted hot-pressing technology

Micro-nano interfacial mechanical interlocking structure-property of the ultrasonic-assisted hot press molded polypropylene/aluminum alloy hybrid

Improving bonding strength of aluminium-PEEK hybrid metal-polymer joints by two-step laser surface treatment

Improving the interfacial bonding strength and suppressing shrinkage porosity of 6061Al/GFRTP hot-pressing joints via interfacial modification

The Influence of Coating and Adhesive Layers on the Mechanical Performance of Additively Manufactured Aluminum–Polymer Hybrid Joints

Comparative Study of Micro-Sized Al Particles Enhancing the Thermal Joining of Aluminum Alloy-Pa66 Without or with Reinforcement

Effect of Metal Surface Topography on the Interlaminar Shear and Tensile Strength of Aluminum/Polyamide 6 Polymer-Metal-Hybrids

Interface needle structure induced high-performance aluminum alloy/PPS hybrids

On the application of strong thermoplastic–thermoset interactions for developing advanced aerospace-composite joints

Enhancement of joint strength of dissimilar aluminum/polymer hybrid joints by friction stir spot welding by surface textures

Achievement of High-strength Al/CFRP Hybrid Joint Via High-speed Friction Stir Lap Joining and Laser Texturing Pretreatment Parameters Variation

Effect of the Polymer on the Joint Strength of Polymer/copper Hybrids Produced by Nano-Injection Molding: Comparison of Polybutylene Terephthalate and Polyphenylene Sulfide Via Experimental and Computational Methods

Adhesion Enhancement of PEEK/6161-T6 FLJ Joints Via Laser Surface Modification

Optimization of Friction Lap Joining Parameters and Exploration Connection Mechanism of CFRPA6/6061-T6 Aluminum Alloy Hybrid Structures

Achieving high strength friction lap spot joints of carbon fiber reinforced thermosetting composite to aluminum alloy with additional thermoplastic interlayer

Hybrid Laser Technique for Joining of Polymer and Titanium Alloy

Analysis of the Thermoplastic Composite Overmolding Process: Interface Strength

A method for manufacturing a mechanically strong and durable hybrid structure of polyethylene–hydroxyapatite composite and titanium alloy

Experimental investigations on mechanical properties of AA6061-T6 aluminum alloy joined by laser welding using digital image correlation

Development and Analysis of a New Joining Method for Polymer-Metal Hybrid Structures