Abstract:Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering, Ahead of Print. The research objectives of pilot diesel injection (PDI) ignition natural gas technology include high efficiency, clean combustion, and low pilot diesel mass. This study is based on a single-cylinder thermodynamic engine, combined with the CONVERGE simulation model and CHEMKIN chemical reaction kinetics model. The effects and mechanisms of various PDI strategies on the mixture equivalent ratio, temperature, and characteristics of combustion and emissions were investigated. The experimental results showed that the best PDI mass was 8 mg/cycle. The thermal atmosphere and activity in the cylinder were improved with an increase in PDI mass from 2 to 8 mg/cycle, which stabilized the mixture combustion. Further, the effects of different pilot injection timing (PIT) on combustion and emissions were investigated via experiments and simulation by controlling the operating conditions and maintaining a constant PDI total mass. The results show that the diesel had a single low-temperature reaction path when the PIT was close to the top dead center, whereas the PIT at the early stage of the compression stroke (CS) changed the chemical reaction path and accelerated the transformation of CH3 to CH2O, accumulating numerous active groups and accelerating the combustion rate, which is difficult to control the ignition phase. The reaction path of the double PDI strategy was similar to that of the PIT at the early CS stage, and its combustion is closed to premixed combustion; however, the accumulation of active groups was relatively small, and the combustion rate was relatively slow because the ignition phase was controlled by the second PDI, making the combustion phase easy to control. Finally, with the double PDI strategy that had the advantages of efficient combustion and avoidance of knock, the gross indicated thermal efficiency reached 49.3% that involved a −60°crank angle (CA) after top dead center (ATDC) first injection and −4°CA ATDC second injection.

Stratified combustion characteristics analysis and assisted-ignition strategy optimization in a natural gas blended diesel Wankel engine

Analysis of Two-Stage Natural-Gas Lean Combustion Inside a Diesel Geometry

Effect of Spark Timing on the Combustion Stages Seen in a Heavy-Duty Compression-Ignition Engine Retrofitted to Natural Gas Spark-Ignition Operation

Methodology to Separate the Two Burn Stages of Natural-Gas Lean Premixed-Combustion Inside a Diesel Geometry

Multiple Combustion Stages Inside a Heavy-Duty Diesel Engine Retrofitted to Natural-Gas Spark-Ignition Operation

Improved Thermodynamic Model for Lean Natural Gas Spark Ignition in a Diesel Engine Using a Triple Wiebe Function

Flame Development Analysis in a Diesel Optical Engine Converted to Spark Ignition Natural Gas Operation

Single and Double Wiebe Function Combustion Model for a Heavy-Duty Diesel Engine Retrofitted to Natural-Gas Spark-Ignition

Two-Stage Lean-Burn Combustion Inside a Natural-Gas Spark-Ignition Engine with a Bowl-in-Piston Chamber

An Experimental Study of the Combustion Process in a Natural-Gas Spark-Ignition Engine

Investigation of Multistage Combustion Inside a Heavy-Duty Natural-Gas Spark-Ignition Engine Using Three-Dimensional Computational Fluid Dynamics Simulations and the Wiebe-Function Combustion Model

Twin-Peak Heat Release Phenomenon Inside a Heavy-Duty Diesel Engine Retrofitted to Natural-Gas Spark Ignition

Assessment of spark-energy allocation and ignition environment on lean combustion in a twin-plug Wankel engine

Optimization of Complex-Guided Stratified Charge Combustion System for Direct Injection Methanol Engine

The effect of ignition diesel injection conditions on the combustion process of natural gas engine

Effect analysis of the forward flow fuel injection angle on stratified combustion process in a high-pressure direct injection diesel Wankel engine (HPDI-DWE)

Realizing stratified mixtures distribution in a hydrogen-enriched gasoline Wankel engine by different compound intake methods

Effect of In-Cylinder Low-Pressure Direct Injection Strategy on the Atomization and Combustion Process of a Small-Scaled Gasoline Wankel Rotary Engine

Investigations on combustion system optimization of a heavy-duty natural gas engine

Optimization of a diesel/natural gas dual fuel engine under different diesel substitution ratios

Effects and mechanism of pilot diesel injection strategies on combustion and emissions of natural gas engine