Abstract:A n-butanol/diesel spray test system was constructed to conduct common rail bench test and constant volume bomb experiments in present work to investigate the impact of different n-butanol blending ratios on spray characteristics and the spray evolution process. To be specific, the research was carried out under the n-butanol blending ratios ofwith 0, 10%, 20%and 40% respectively to study various n-butanol blending ratio effects and to analyze the variation of the physical and chemical characteristics of the fuel. Then, the fuel spray patterns data at 0.4 ms was carefully collected and analyzed to compar the effect of different n-butanol blending ratios on spray penetration and spray angle. In addition, an-butanol/diesel spray model in engine cylinder was also established, to analyze how spray penetration and SMD of blended fuel varied during spray process, , as well as the impacts of n-butanol blending ratios on evaporation characteristics of blended fuel. Furthermore the various changes in velocity field and number density field in spray processes with different blending ratios have been taken into consideration and discussed for more detailed problems. It can be observed from the research data that: in normal temperature and pressure region,as the n-butanol blending ratio increased,the spray penetration decreased and there was a moderate rise in spray angle during spray process; as blending ratios of n-butanol increased by 40%, the spray penetration slightly reduced by 4.95%while reversely the spray angle climbed by 16.7%. Also when the injection pressure ascended, there was obvious rise both in the spray penetration and spray angle, particularly, if injection pressure rose by 40 MPa , the spray angle increased by 28.43°. During the spray evolution process, the n-butanol blending ratios influenced the spray penetration slightly, while in the very initial step of fuel blending process, the higher the n-butanol blending ratio was, the smaller SMD of blended fuel became. Along with the development of the spray process, however, the ultimate spray penetrations of different blended fuel were basically the same. In the injecting duration period, with the increasing of n-butanol blending ratio, there was a substantial drop in the mass of the fuel injected into the cylinder, and the peak velocity value of the jet dropped distinctly. Moreover, as a result of the fall in the viscosity and surface tension, the volatilization of blended fuel was apparently enhanced and subsequently fuel evaporation mass was increased slightly. The n-butanol blending ratios had quite limited impact on number density of drops but obviously facilitated the spray period, that is, the larger the blend ratio was, the better the spray characteristics would be. Besides this, in the central region of the downstream jet the figure of number density reached the highest.

The Influence of Butanol-Acetone (BA) Mixture on Spray and Performance Characteristics of Castor and Pongamia Biodiesel

The Effect of Different Mixing Proportions and Different Operating Conditions of Biodiesel Blended Fuel on Emissions and Performance of Compression Ignition Engines

Spray behavior of butanol-diesel and numerical simulation of mixture formation with engine

Influence of Fuel Filterability, Performance, and Emission Characteristics of Dual Biodiesel Mixture with Diesel Blends in Compression Ignition Engine

Experimental Investigation on the Effect of N-Butanol Blending on Spray Characteristics of Soybean Biodiesel in a Common-Rail Fuel Injection System

Effect of small proportion of butanol additive on the performance, emission, and combustion of Australian native first- and second-generation biodiesel in a diesel engine

Role of injection pressure on fuel atomization and spray penetration on the Thevetia peruviana and Jatropha curcas biodiesel blends with nanoparticle

Determination of the Optimum Blend Ratio of Diesel, Waste Oil Derived Biodiesel and 1-Pentanol Using the Response Surface Method

Evaluation of Aluminum Oxide Nanoparticle Blended with Alcohol Based Biodiesel at Variable Compression Ratios

Improving Of Ci Engine Performance Using Three Different Types Of Biodiesel

Comparative thermal assessment and emission analysis of various green biodiesel from novel feedstocks for CI engines: a sustainable approach towards emission reduction

The performance, emissions, and combustion characteristics of an unmodified diesel engine running on the ternary blends of pentanol/safflower oil biodiesel/diesel fuel

Experimental investigation on the characteristics of ternary blended fuel using Artocarpus heterophyllus peel: a sustainable fuel for gasoline engine applications

Performance and emission characteristics of novel biodiesel-diesel blends: an RSM and ANN approach

Multi-objective optimization of ternary blends of Algal biodiesel-diesel-1-decanol to mitigate environmental pollution in powering a diesel engine using RSM, ANOVA, and artificial bee colony

Influence of Injection Timing on Performance and Combustion Characteristics of Compression Ignition Engine Working on Quaternary Blends of Diesel Fuel, Mixed Biodiesel, and T-Butyl Peroxide

Experimental assessment of catalytic biofuel effect on performance and exhaust emission of diesel engine

Experimental investigation of quaternary blends of diesel/hybrid biodiesel/vegetable oil/heptanol as a potential feedstock on performance, combustion, and emission characteristics in a CI engine

Performance Characteristics of Diesel Engine Using Biodiesel Blends

Evaluation of Sooting Tendency of Acetone–butanol–ethanol (ABE) Fuels Blended with Diesel Fuel

Multi‐aspect assessment and multi‐objective optimization of preheated tallow biodiesel‐diesel blend as alternate fuel in CI engine