Abstract:Abstract This paper describes the strategies and practices used to deliver best in class ROP performance in three different applications (through salt, soft clastic and medium-hard clastic formations) on the Deepwater Gulf of Mexico. A novel advanced bit design was tested with mechanical (WOB and RPM) and hydraulic (flow rate) parameters beyond the current operational envelope. Several operational and equipment limits were also tested and moved beyond the previous levels. The drilling parameters and results from the three applications are also included. Over the last couple of years, the drilling cost for deep-water drilling has been reduced through continuous performance improvement resulting in a "Beyond the Best" mentality. Every time a new best in class ROP performance is achieved, questions about "What else can be done", are asked. A project was taken up to challenge the current drilling operational envelope resulting in ROPs faster than ever in the Deepwater Gulf of Mexico. Integrated well planning combining operator and service provider knowhow and modeling capability were used to identify current operational limits and the required changes to go beyond them. BHA configuration and downhole tools were design and adjusted accordingly. Rig equipment were also reviewed and modified. The novel advanced bit design, with 3D cutting elements combining the shearing action of conventional PDC cutters with the crushing action of tungsten carbide insert, was selected by the project due to its capability of delivering less torque when higher mechanical parameters (WOB and RPM) are used. Field data demonstrates that using WOB up to 70,000 lbs while drilling with a 14-3/4" bit through medium-hard rock resulted in 9 % increase in ROP (103.2 ft/hr), when compared with the previous fastest ROP achieved while drilling similar formations in the field. Also, using 220 rpm while drilling trough salt with a 16-1/2" bit delivered 12% increase in ROP (307.3 ft/hr), when compared with the previous best performance. Furthermore, using 220 rpm in combination with 1460 gpm flow rate (22% above the normal flow rate), while drilling with a similar 16-1/2" bit through interbedded soft rock formations delivered 91% increase in ROP (368.7 ft/hr), when compared with the previous fastest ROP achieved while drilling similar formations in the field. The cuttings load limit in the annulus was tested beyond its current limit (3%) without observing hole pack off or stuck pipe issues. No vibration was observed while operating at the surface torque limit. A cost saving of over $2M was realized from this performance improvement effort. The identified opportunities for improvement and lessons learned included in the paper have led to best practices for future wells resulting in a valuable benchmark benefiting practicing engineer involved in similar projects. Furthermore, operational parameters used in the project confirm the robustness and benefits of the novel advanced bit design used in the project delivering higher ROP with a smooth torque response.

The stress field simulation of a novel M-type convex stepped bottomhole and the rate of penetration enhancement mechanism of a new type of central-grooved PDC bit for offshore deep & ultradeep well drilling

Rock-Breaking Mechanism Study of Axial and Torsional Impact Hammer and Its Application in Deep Wells

Structure design of weight-on-bit self-adjusting PDC bit based on stress field analysis and experiment evaluation

Research on Weight-on-bit Self-adjusting Dual-diameter PDC Bit Design and Effect Evaluation Utilizing Stress-Releasing Effect of Rock at Bottomhole

Design and comparative analysis of self-propelling drill bit applied to deep-sea stratum drilling robot

Selection and Optimization Design of PDC Bits Based on FEM Analysis for Drilling Long Horizontal Sections of Shale Formations

Experimental and theoretical analysis of rock failure characteristics by a single PDC cutter under downhole pressurized conditions

Evaluation of rock-bit interaction test under simulated ultra-deep well conditions based on similarity principle

The PDC cutter-rock interaction behavior in rock cutting: A review

Analysis of Bottomhole Rock Stress in Deep-Well Drilling Considering Thermal-Hydro-Mechanical Coupling

Characterizing Rock-Breaking Performance of PDC Cutters via Stability Metrics and Energy consumption in FDEM Simulations

Research on the Temperature Field Distribution Characteristics of Bottomhole PDC Bits during the Efficient Development of Unconventional Oil and Gas in Long Horizontal Wells

Study on rock breaking mechanism of PDC bit with rotating module

Study on Composite Rock-Breaking Mechanism of Ultrahigh-Pressure Water Jet–PDC Cutter

3D numerical simulation study of rock breaking of the wavy PDC cutter and field verification

Drilling Efficiently, Durably and Consistently Through Cherts and Conglomerates with PDC Bits is Possible

Study on Techniques and Application of New Bits for Difficult Formation in Piedmont Region

Delivering Best in Class ROP Performance by Pushing the Operational Envelope with Novel Advanced Bit Designs

Study on the mechanism of multidimensional cutting teeth and the influencing factors of rock breaking efficiency

DEM numerical investigation on the effect of back rake angle of PDC bit in drilling hard rock strata

Research on numerical drilling technology of mesh-like cutting PDC bit