Abstract:The properties of the extracellular matrix (ECM) have profound impact upon cell behaviour. As an abundant protein in mammals, collagen is a desirable base material to engineer an ECM tissue scaffold, but its structural weakness generally requires molecular crosslinking or incorporation of additional ECM-based macromolecules such as glycosaminoglycans. We have performed microscopic indentation to test collagen films under dry and aqueous conditions prepared with different levels of physical and chemical crosslinking. Our technique isolates intrinsic properties of the poro-viscoelastic matrix in a regime minimizing the influence of drainage hydrodynamics and allows direct measurement of the effect of hydrating a specific sample. A doubling of the effective stress-strain stiffness under crosslinking could be directly correlated to structural changes in X-ray diffraction spectra, while electron microscopy revealed possible fibril bridging mechanisms explaining observed toughness. Overall, an intrinsic viscoelastic stress-strain response of collagen under various conditions of cross-linking was observed for both dry and wet conditions, with the latter most affected by indentation rate. Under creep testing, a three order of magnitude increase in dynamic compliance and factor three reduction in relaxation time was found going from the dry to hydrated state. When fitted to a simple viscoelastic model, crosslinking showed a tendency to decrease relaxation time in both states, but reduced dynamic compliance only in the hydrated case. This suggests a reduced role of virtual crosslinks under hydration. This is the first study reporting consistent mechanical testing of dry and hydrated ECM-derived biomaterials, accessing the intrinsic material mechanics under in vivo-like conditions. STATEMENT OF SIGNIFICANCE: This manuscript presents new insights into the effect of crosslinking on mechanical properties of dry and hydrated collagen intended for tissue scaffolding applications. A novel microscopic indentation technique allowed testing of the poro-viscoelastic matrix isolated in a regime minimizing the influence of drainage hydrodynamics, so direct comparison of the effect of hydration on the intrinsic material behaviour to could be made. A variety of experimental techniques including X-ray diffraction, infrared spectroscopy, and scanning electron and atomic force microscopy were used to augment the mechanical testing. The results of creep testing were numerically analysed using a four-component viscoelastic model. This is the first mechanical testing of dry and hydrated ECM-derived biomaterials, accessing the intrinsic material mechanics under in vivo-like conditions.

Force measurement study of engineered collagen-chitosan scaffold using Atomic Force Microscopy

From Common Biomass Materials to High-Performance Tissue Engineering Scaffold: Biomimetic Preparation, Properties Characterization, in Vitro and in Vivo Evaluations

Evaluation of Stem Cell-to-Tenocyte Differentiation by Atomic Force Microscopy to Measure Cellular Elastic Moduli

Mechanical Enhancement and in Vitro Biocompatibility of Nanofibrous Collagen-Chitosan Scaffolds for Tissue Engineering

Effect of nanostructure of mineralized collagen scaffolds on their physical properties and osteogenic potential.

Effect of cross-linking and hydration on microscale flat punch indentation contact to collagen-hyaluronic acid films in the viscoelastic limit

Hyperelastic characterization reveals proteoglycans drive the nanoscale strain-stiffening response in hyaline cartilage

In-silico modeling of the micromechanics of fibrous scaffolds and stiffness sensing by cells

An Apparatus for Measuring Combined Shear-Tensile Loading in Fibrous Tissues Ex Vivo

Probing Micromechanical Properties of the Extracellular Matrix of Soft Tissues by Atomic Force Microscopy

Ultrastructural viscoelastic behavior of collagen identified by AFM nano-dynamic mechanical analysis

Micropore-array Confining Assisted Young's Modulus Measurement of Suspended Cells Using Atomic Force Microscopy

Measuring the elastic modulus of soft culture surfaces and three-dimensional hydrogels using atomic force microscopy

3D in-situ characterization reveals the instability-induced auxetic behavior of collagen scaffolds for tissue engineering

Atomic Force Microscopy Micro-Indentation Methods for Determining the Elastic Modulus of Murine Articular Cartilage

A Study of Strain Distribution and Cell Adhesion of MicroHA/CS Composite Scaffold under Mechanical Loading

Design and Fabrication of Porous Chitosan Scaffolds with Tunable Structures and Mechanical Properties

Construction of ultrasonically treated collagen/silk fibroin composite scaffolds to induce cartilage regeneration

Selection of Force Sensors for In Situ Measurement of Neotissue Microenvironments

Composite Silk-extracellular-matrix Scaffolds for Enhanced Chondrogenesis of Mesenchymal Stem Cells.

Measuring biomaterials mechanics with atomic force microscopy. 1. Influence of the loading rate and applied force (pyramidal tips)