Abstract:For industrial or domestic applications, the wide range of use of pleated filters makes the understanding of their airflow behavior a major issue for designer and users. In all industrial installations dealing with radioactive matter, the containment of pollutants must be ensured. High-efficiency particulate air (HEPA) filters are used as the last purification stage before the air is rejected in the environment. These filters can be used either alone, in the case of nonsensible installation, or coupled with other filtration devices disposed before it where contamination level could be important. The prediction of their pressure drop is very important in nuclear safety to be able to anticipate any dysfunction or rupture of these devices. It has been observed that geometry of the medium has an influence on the pressure drop of a pleated filter. In the case of HEPA filters, no convincing explanation has been brought to explain their airflow behavior. The pressure drop evolution of the filter during the clogging remains difficult to explain by assuming constant pleat geometry. Some studies show that deformation occurs during the filter use, which could induce an increase of the available volume in the pleat and a reduction of the efficient filtration surface. The increase in computation capacity introduces nowadays the possibility to perform complex simulation, taking into account the effect of fluids on sensible devices. This can be the case for simple structural analysis or for more complex analysis such as vibration induced by gas or fluid flow. It is mostly applied to avoid breaking or deformation of safety devices, and this can also be applied to anticipate the fluid behavior of some special devices such as filters. In classical filtration application, properties of the filter are coupled with particle deposition (e.g., changes in geometry and permeability depend on the thickness of the deposit). The studies concerning mechanical properties of filters are mainly performed for liquid filtration and clean filters. For pleated filters, the complexity of this kind of analysis remains the modification of the link between geometry, pressure drop, mechanical strength, and particle transport and accumulation inside the pleat. As a first approach, it has been chosen to combine an experimental and a numerical approach to improve the understanding of filter behavior. In this paper, the pleat deformation will be investigated using a direct nonintrusive laser measurement performed on a single pleat experiment. The rate of filtration surface lost will be estimated using these data and taken into account to evaluate the pressure drop against the filtration velocity. Results obtained show that the pleat deformation is an important parameter, which influences the geometry of the pleat.

Pressure drop in honeycomb adsorption filters filled with granular activated carbon

Fabrication of wall-flow honeycomb micro packed bed and application in pressure swing adsorption process

Prediction of Pressure Drop in Adsorption Filter Using Friction Factor Correlations for Packed Bed

The pressure drop of fibrous surface filters for gas Filtration: Modeling and experimental studies

Numerical Simulation of Fine Particles Trapping Process Using a Wall-Flow Honeycomb Filter

Numerical simulation of a multilayer granular bed filter: Effect of bed structure on the filtration characteristics of high-temperature particulate matter

Filtration characteristics of granular bed with layered drawers for removing dust from gas streams

Pressure Drop Performance of Porous Composites Based on Cotton Cellulose Nanofiber and Aramid Nanofiber for Cigarette Filter Rod

A numerical simulation method for pressure drop and normal air velocity of pleated filters during dust loading

Filtration performance and loading capacity of nano-structured composite filter media for applications with high soot concentrations

Experimental study on filtration characteristics of a novel moving granular bed filter

Effects of the filter media pack configurations on the air filtration performance

Interaction of water mists with bibulous filter media and hygroscopic particles in pressure drop jump of fibrous filter media

Experimental Study on Resistance Influencing Factors of Clean Filter Material Used in Air Purification

Experimental validation of adsorption filter model under dynamic VOC concentrations: Prediction of long-term efficiency

Experimental and Numerical Investigation of Slip Effect on Nanofiber Filter Performance at Low Pressures

Adjustable fiber structure design for precise aerosol filtration

Influence of pleated geometry on the pressure drop of filters during dust loading process: experimental and modelling study

Experimental study on pressure drop profiles of one-way flow and reciprocal flow in honeycomb regenerator system

Influence of Pleat Deformation on Pressure Drop for a High-Efficiency Particulate Air Filter: A Small-Scale Experimental Approach

Experiment and Prediction of Pressure Drop in a Fiber–Powder Composite Material with Porous Structure for Energy Wheels and Air Cleaners