Abstract:In this study, ionic liquids and carbon nanotubes were used to prepare PEI composite fibers (PEI/CNT‐IL) successfully. When the contents of CNT and IL are 0.5% and 1.0%, respectively, PEI/CNT‐IL composite fiber can realize the optimal performance. PEI/0.5%CNT‐1.0%IL composite fiber achieves the breaking stress of 2.0 cN/dtex, and the electrical conductivity of 1.06×10‐5 S/cm without any negative influence on the heat resistance. Polyetherimide (PEI) has been widely applied in the form of plastics, films, and foam materials. But PEI fiber is confronted with some challenges, such as high melt viscosity and high spinning temperature during the spinning process, poor mechanical properties because of its amorphous structure. In this study, ionic liquids (ILs) and carbon nanotubes (CNTs) were used to prepare PEI composite fibers (PEI/CNT‐IL) successfully, which were further characterized by scanning electron microscope (SEM), Raman spectra, differential scanning calorimetry, dynamic mechanical analysis, thermalgravimetric analysis, mechanical property, and conductivity measurements. IL showed a plasticizing effect to reduce the processing temperature of PEI and SEM images showed that CNTs were uniformly dispersed in the PEI matrix by the assistance of IL. The synergistic effect of CNT and IL thus improved the tensile strength and antistatic properties of PEI fibers. When the contents of CNT and IL were 0.5 and 1.0 wt%, respectively, the optimal properties were obtained. PEI/CNT‐IL fibers exhibited a maximum tensile strength of 2.0 cN/dtex with the elongation at break being 90%, and the enhanced electrical conductivity of 10−5 S·cm−1, which was increased by 13 orders of magnitude compared to that of pristine PEI fiber. Highlights PEI composite fibers were prepared via melt spinning with the assistance of IL and CNT. IL can effectively disperse CNT and plasticize PEI to reduce the processing temperature. The synergistic effect of CNT and IL has improved the tensile strength and antistatic properties of PEI fibers.

Preparation and properties of high‐strength‐high‐modulus polyimide cords/natural rubber composites

Cure of Neat Resins and Properties of Composites for Interpenetrating Polymer Networks from the Novel Bismaleimide and Cyanate Containing Naphthalene

Enhanced Mechanical Properties of Natural Rubber by Block Copolymer-Based Porous Carbon Fibers

Interface construction and properties of polyester fibers reinforced acrylonitrile-butadiene rubber coordination composites

Microwave Irradiated Polyester Staple Fibers for Natural Rubber with Excellent Interface Performance

Fabricating super tough polylactic acid based composites by interfacial compatibilization of imidazolium polyurethane modified carbon nanotubes

Self‐reinforced natural rubber composites: Preparation and properties study

The characterization and properties of low linear density polyethyelene (LLDPE)/ acrylonitrile butadiene rubber (NBR)/ palm press fiber (PPF) with γ-aminopropyltriethoxysilane coupling agent

Improved Adhesion of Rubber Composites by Developing Environmentally Friendly Fiber Impregnation Coatings with Good Interfacial Modulus Transition Gradients

Cure kinetics and morphology of natural rubber reinforced by the in situ polymerization of zinc dimethacrylate

A new eco-friendly dipping system for PA66 fiber cords/rubber composites with strong interfacial adhesion and good fatigue stability

Functional interface with polyaniline in UHMWPE fiber‐reinforced composites for enhanced interfacial adhesion and damage monitoring

Fabrication and properties of high performance polyimide nanofibrous films by electrospinning

A novel PDA/POSS transition layer on the surface of UHMWPE fibers by co-depositing to improve the mechanical properties of composites

Molding process and properties of polyimide-fiber-fabric-reinforced polyether ether ketone composites

High-performance Polyphenylene Sulfide Composites with Ultra-High Content of Glass Fiber Fabrics

Preparation and properties of polyetherimide fibers based on the synergistic effect of carbon nanotubes and ionic liquids

A dopamine-like deposition coatings on the polyethylene terephthalate fibers and its interface adhesion with rubber

Interfacial enhancement by constructing a "flexible-rigid" structure between high-modulus fillers and low-modulus matrix in carbon fiber/silicone rubber composites

Enhancing Performances of Polyamide 66 Short Fiber/Natural Rubber Composites via In Situ Vulcanization Reaction

Highly flame retardant, strength, and tough epoxy resins and CFRPs via introducing a self-assembly novel ionic bond, rigid-flexible structure PPI