Abstract:The aim of this study was to investigate the influence of fineness and heat-treatment on the pozzolanic and engineering properties of volcanic ash. To this end, two different fineness levels of volcanic ash, ultra-fine (VAF) and fine (VA), without and after heat treatment at different temperatures (VA550, VA650, and VA750), were partially substituted for cement. In addition to the control (100% cement), five binary mortar mixes, each containing 20% of the different types of volcanic ash (VAF and VA; heat-treated and not), were prepared. First, X-ray fluorescence (XRF), X-ray powder diffraction (XRD), particle size analysis, and modified Chappelle tests were used to characterize the material. All mortar mixes were then tested for compressive strength development, water absorption, and apparent porosity. Finally, the microstructure of each of the mixes was evaluated by performing XRD, thermogravimetric analysis (TGA), and Fourier transform infrared spectroscopy (FTIR) analyses on paste samples at 91 days post-formation. The XRD and Chappelle reactivity results revealed increased pozzolanic reactivity with increasing volcanic ash fineness. In contrast, heat treatment adversely affected the pozzolanic reactivity of the volcanic ash due to the formation of crystalline phases at high temperatures. The mortars containing VAF20 (VAF, no heat, at 20%) showed slightly improved compressive strength (69.6 MPa) than the control (68.1 MPa) and all other binary mixes (66.7, 63.5, 64.2, and 63.9 MPa for VA20, VA20-550, VA20-650, and VA20-750, respectively) at 91 days. The mortar containing VAF20 demonstrated the lowest level of water absorption (9.3%) and apparent porosity (19.1%) of all mixes, including the control. The XRD results for the paste samples show that both VA and VAF showed the least intensity of portlandite phase, as compared to the control and other binary mixes. TGA results also show that binary mixes of VA and VAF have a reduced amount of portlandite, resulting in the densification of the mixes’ microstructures. With the addition of VAF, there is a significant shift in the FTIR band from 980 to 992 cm−1, which causes the formation of additional C–S–H gels that lead to the densification of the paste matrix. These results demonstrate that VAF exhibits high pozzolanic reactivity, making it suitable for use as a natural pozzolan that can partially substitute cement in the production of strong, durable, and environmentally friendly concrete.

The effect of physical properties of pond ash as a partial replacement of sand in the mortar mix

Evaluation of mechanical properties of cement mortars containing pond ash as partial replacement of river sand and prediction of properties by regression models

Valorization of waste pond ash in cement mortars and prediction of mechanical properties by simple linear regression

Development of novel mortar using fine river sand and pretreated waste flue gas desulfurization gypsum powder and pond fly ash

Effect of Wood Ash on salt Crystallization and Rapid Chloride Permeability Test (RPCT) in Mortar

Effect of Replacing Fine Aggregate with Fly Ash on the Performance of Mortar

Synergy of Hydration and Microstructural Properties of Sustainable Cement Mortar Supplemented with Industrial By-Products

Experimental Study on Partial Replacement of Materials like Industrial Waste & Rice Husk with Clay Mortar

Sustainable cement mortar production using rice husk and eggshell powder: a study of strength, electrical resistivity, and microstructure

Characterisation of domestically discarded vegetable waste biomass ash and silica sand mixed with ordinary Portland cement concrete

PROPERTIES OF CEMENT-FLY ASH MIXTURES WITH SUBSTANDARD FLY ASH AS A PARTIAL CEMENT AND FINE AGGREGATE REPLACEMENT

Effect of Fineness of Basaltic Volcanic Ash on Pozzolanic Reactivity, ASR Expansion and Drying Shrinkage of Blended Cement Mortars

Mechanical and Durability Properties of Mortars Incorporating Red Mud, Ground Granulated Blast Furnace Slag, and Electric Arc Furnace Dust

Sugarcane bagasse ash as supplementary cementitious material in cement composites: strength, durability, and microstructural analysis

Impact of M-Sand on Rheological, Mechanical, and Microstructural Properties of Self-Compacting Concrete

Properties and microstructure of concrete using pozzolanic materials and manufactured sand as partial replacement of fine aggregate

Effect of Fineness and Heat Treatment on the Pozzolanic Activity of Natural Volcanic Ash for Its Utilization as Supplementary Cementitious Materials

Effect of Rice Husk Ash and Water-Cement Ratio on Strength of Concrete

Properties of Mortars Formulated from Self-Compacting High-Performance Concrete Containing Various Mineral Additions

Analyzing the Mechanical, Durability, and Microstructural Impact of Partial Cement Replacement with Pumice Powder and Bamboo Leaf Ash in Concrete

Effects of varied building solid wastes, particle sizes and substitution ratios on the performance and impedance spectrum of recycled fine aggregate mortar and the feasibility of developing a prediction method