Abstract:Over the past few years, owing to different critical features such as high energy densities, safety, cycle-life etc., Lithium-ion batteries have been used successfully as an energy storage system for automotive applications. In addition, due to recent increase in interests towards developing EVTOL (Electric Vertical Take-Off and Landing) aircrafts, demand for Li-Ion batteries capable of providing high power discharge and charge along with above mentioned features has increased. Thermal Management System (TMS) is a critical component of a Li-Ion battery system that enables sustained high-power peak performance, improves overall life-cycle, and reduces possibility of thermal runaway during regular vehicle operation. The current article studies two different cooling configurations for thermal management of a commercially available 9 A-h Nickel Manganese Cobalt (NMC) Lithium-ion pouch cell for high C-rate conditions. The two configurations are referred to as the Double-sided cooling and Hybrid cooling, which includes a novel approach utilizing graphite-based heat spreader. The thermal performance for both configurations are studied through experimental testing and CFD (computational fluid dynamics) modeling. During experimental analysis, the pouch cell was subjected to high C-rate discharges of 3C, 4C and 5C using an Arbin controller and thermal test bench including a cold plate, mass flow meter, and temperature sensors. The temperature response of the cell is measured using T-type thermocouples that are strategically installed on its surface using a thermal interface material. For the numerical analysis, time-accurate, conjugate heat transfer-based 3D CFD simulations are conducted on high spatial resolution grids with a commercially available finite-volume method based CFD software. Numerical simulations at the mentioned C-rates are then run to explore the overall temperature distribution on the cell body. Temperature estimates from the numerical model are compared to the test data for the most aggressive 5C discharge condition. Both experimental testing and numerical modeling show that the Hybrid cooling approach provides higher rate of heat transfer compared to Double-sided cooling, owing to high thermal conductivity of graphite. Average cell surface temperatures using Hybrid cooling are ∼3°C, 3.7°C and 4.3°C lower than Double-sided cooling for 3C, 4C and 5C discharge conditions, respectively. The maximum measured cell temperature at the end of the most aggressive 5C discharge is 6°C lower in the case of Hybrid cooling. The temperature gradients are also less aggressive thereby allowing for a more uniform temperature distribution within the cell. Additional results in terms of flow and temperature distributions are also provided for the cold plate present in the cooling setup.

Development of electro-thermal model for prismatic Lithium-ion cell subjected to electric vehicle drive cycle using converging fluid channel

Theoretical and Experimental Investigations on Liquid Immersion Cooling Battery Packs for Electric Vehicles Based on Analysis of Battery Heat Generation Characteristics

A composite electrochemical-thermal model for the determination of thermal profiles of lithium-ion cell for electric vehicle application

Thermal Performance Analysis of Liquid Cooling System in Lithium-ion Battery

Thermo-electrochemical model for forced convection air cooling of a lithium-ion battery module

Thermal characterization of pouch cell using infrared thermography and electrochemical modelling for the Design of Effective Battery Thermal Management System

Numerical Simulation of Lithium-ion Battery Cooling Techniques for Electric Vehicles

Experimental and computational analysis on lithium-ion battery thermal management system utilizing air cooling with radial fins

Computational Design and Analysis of a Novel Battery Thermal Management System of a Single 26650 Li-Ion Battery Cell for Electric Vehicle Application

Development and Analysis of a New Cylindrical Lithium-Ion Battery Thermal Management System

High Reynold’s Number Turbulent Model for Micro-Channel Cold Plate Using Reverse Engineering Approach for Water-Cooled Battery in Electric Vehicles

Computational Fluid Dynamics-Based Numerical Analysis for Studying the Effect of Mini-Channel Cooling Plate, Flow Characteristics, and Battery Arrangement for Cylindrical Lithium-Ion Battery Pack

Thermal behavior study of discharging/charging cylindrical lithium-ion battery module cooled by channeled liquid flow

CFD and Experimental Investigation of Graphite Heat Spreader Based Cooling for Li-Ion Batteries for Electric Vehicles and EVTOL (Electric Vertical Take-Off and Landing) Aircraft Applications

Performance evaluation of a hydrostatic flow immersion cooling system for high-current discharge Li-ion batteries

Study on effect of diverse air inlet arrangement on thermal management of cylindrical lithium-ion cells

Optimization of 1D/3D Electro-Thermal Model for Liquid-Cooled Lithium-Ion Capacitor Module in High Power Applications

Battery Thermal Management System Design: Role of Influence of Nanofluids, Flow Directions, and Channels

Thermal performance assessment for an array of cylindrical Lithium-Ion battery cells using an Air-Cooling system

Analytical modeling and simulation of liquid cooling thermal management of a lithium-ion battery module

Modeling and Analysis of Heat Dissipation for Liquid Cooling Lithium-Ion Batteries