Abstract:Thermal energy storage systems open up high potentials for improvements in efficiency and flexibility for power plant and industrial applications. Transferring such technologies as basis for thermal management concepts in battery-electric vehicles allow alternative ways for heating the interior and avoid range limitations during cold seasons. The idea of such concepts is to generate heat electrically (power-to-heat) parallel of charging the battery, store it efficiently and discharge heat at a defined temperature level. The successful application of such concepts requires two central prerequisites: higher systemic storage densities compared to today’s battery-powered PTC heaters as well as high charging and discharging powers. A promising approach for both requirements is based on solids as thermal energy storage. These allow during discharging an efficient heat transfer to the gaseous heat transfer medium (air) due to a wide range of geometric configurations with high specific surfaces and during charging high storage densities due to use of ceramic materials suitable for high operating temperatures. However, for such concepts suitable heating systems with small dimensions are needed, allowing an efficient and homogeneous heat transfer to the solid with high charging powers and high heating temperatures. An appropriate technology for this purpose is based on resistance heating wires integrated inside the channel shaped solids. These promise high storage densities due to operating wire temperature of up to 1300 °C and an efficient heat transport via radiation. Such electrically heated storage systems have been known for a long time for stationary applications, e.g., domestic storage heaters, but are new for mobile applications. For evaluation such concepts with regard to systemic storage and power density as well as to identify preferred configurations extensive investigations are necessary. For this purpose, transient models for the relevant heat transport mechanisms and the whole storage system were created. In order to allow time-efficient simulations studies for such an electrical heated storage system, a novel correlation for the effective radiation coefficient based on the Fourier Number was derived. This coefficient includes radiation effects and thermal conduction resistances and enables through its dimensionless parameterization the investigation of the charging process for a wide range of geometrical configurations. Based on application-typical specifications and the derived Fourier based correlation, extensive variation studies regarding the storage system were performed and evaluated with respect to systemic storage densities, heating wire surface loads and dimensions. For a favored design option selected here, maximum systemic storage densities of 201 Wh/kg at maximum heating wire surface loads of 4.6 W/cm2 are achieved showing significant benefits compared to today’s battery powered PTC heaters. Additionally, for proofing and confirming the storage concept, a test rig was erected focusing experimental investigations on the charging process. For a first experimental setup-up including all relevant components, mean temperature-related deviations between the simulative and the experimental results of 4.1% were detected and storage temperatures of up to 870 °C were reached. The systematically performed results confirm the feasibility, high efficiency, thermodynamic synergies with geometric requirements during thermal discharging and the potential of the technology to reach higher systemic storage densities compared to current solutions.

Type II absorption thermal battery for temperature upgrading: Energy storage heat transformer

A Hybrid Resorption-Compression Heat Transformer for Energy Storage and Upgrade with a Large Temperature Lift

A novel double-effect compression-assisted absorption thermal battery with high storage performance for thermal energy storage

Experimental Investigation on an Innovative Resorption System for Energy Storage and Upgrade

High-Performance Cascade Sorption Thermal Storage Battery for Long-Term Applications in Cold Regions

A hybrid compression-assisted absorption thermal battery with high energy storage density/efficiency and low charging temperature

On the rational development of advanced thermochemical thermal batteries for short-term and long-term energy storage

Experimental study on a two-stage absorption thermal battery with absorption-enhanced generation for high storage density and extremely low charging temperature (∼50 °C)

Integrated Energy Storage and Energy Upgrade of Low-Grade Thermal Energy Based on Thermochemical Resorption Heat Transformer

Solid Sorption Thermal Battery Assisted by Continuous Compression Process for Efficient Heat Supply

Heat Pump Assisted Open Three-Phase Sorption Thermal Battery for Efficient Heat Storage

Ammonia-based Sorption Thermal Battery: Concepts, Thermal Cycles, Applications, and Perspectives

Experimental Study on Heat Release Performance for Sorption Thermal Battery Based on Wave Analysis Method

A novel compression-assisted energy storage heat transformer for low-grade renewable energy utilization

Performance Analysis On A Hybrid Compression-Assisted Sorption Thermal Battery For Seasonal Heat Storage In Severe Cold Region

A phase-change-material-assisted absorption thermal battery for space heating under low ambient temperatures

Compression-assisted Adsorption Thermal Battery Based on Composite Sorbent for Heat Supply in Alpine Cold Region

Performance Mapping of an Open Absorption Thermal Battery with Crystallization and Sorbent Circulation

Development of Sorption Thermal Battery for Low-Grade Waste Heat Recovery and Combined Cold and Heat Energy Storage

Enhanced Thermally Integrated Carnot Battery Using Low-Gwp Working Fluid Pair: Multi-aspect Analysis and Multi-Scale Optimization

Thermal Battery for Electric Vehicles: High-Temperature Heating System for Solid Media Based Thermal Energy Storages