One-Year Evaluation of High-Power Rapid Curing on Dentin Bond Strength

Eva Klarić,Josipa Vukelja Bosnić,Matej Par,Zrinka Tarle,Danijela Marovic
DOI: https://doi.org/10.3390/ma17102297
IF: 3.4
2024-05-14
Materials
Abstract:This study investigated the effect of 3 s light-curing with a high-power LED curing unit on the shear bond strength of bulk-fill composites. Four bulk-fill composites were bonded to dentin with a universal adhesive (Scotchbond Universal Plus): two materials designed for rapid curing (Tetric PowerFill and Tetric PowerFlow) and two controls (Filtek One Bulk Fill Restorative and SDR Plus Bulk Fill Flowable). The 4 mm composite layer was light-cured with Bluephase PowerCure for 20 s at 1000 mW/cm2 ("20 s") or for 3 s at 3000 mW/cm2 ("3 s"). The samples were stored at 37 °C in distilled water and tested after 1, 6 and 12 months. The samples polymerised in the "3 s" mode had statistically similar or higher bond strength than the samples cured in "20 s" mode, except for the Tetric PowerFlow (1 month) and SDR+ (6 month). The flowable materials Tetric PowerFlow and SDR Plus initially showed the highest values in the "3 s" and "20 s" groups, which decreased after 12 months. The bond strength was statistically similar for all materials and curing protocols after 12 months, except for Tetric PowerFill cured with the "3 s" protocol (21.22 ± 5.0 MPa), which showed the highest value. Tetric PowerFill showed the highest long-term bond strength. While "3 s" curing resulted in equal or better shear bond strength, its use can only be recommended for a material with an AFCT agent such as Tetric PowerFill.
materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
What problem does this paper attempt to address?
The problem this paper attempts to address is the evaluation of the long-term effects of high-power rapid curing (3 seconds) on dentin bond strength. Specifically, the researchers aim to investigate whether this rapid curing method can maintain or improve bond strength comparable to the traditional 20-second curing method by using a high-power LED curing unit to cure four different types of resin materials (two designed for rapid curing and two control materials) within 3 seconds. Additionally, the study aims to determine the types of bonds (adhesive, cohesive, or mixed) formed by different materials under different curing methods. ### Main Issues: 1. **Impact of high-power rapid curing on bond strength**: The researchers want to understand whether 3-second high-power curing can maintain or improve dentin bond strength compared to the traditional 20-second curing method. 2. **Differences in response among different materials**: The researchers also aim to explore the performance differences of various types of resin materials (especially those designed for rapid curing) under 3-second and 20-second curing. 3. **Long-term stability**: The researchers are concerned with the changes in bond strength of these materials after 1, 6, and 12 months to assess their long-term stability. ### Research Background: - **Importance of bonding in dentistry**: Bonding is the cornerstone of modern restorative dentistry, but the need to simplify and shorten clinical procedures may compromise bonding effectiveness. - **Development of rapid curing technology**: Manufacturers have introduced high-performance light sources for 3-second rapid curing to meet clinical demands. At the same time, the development of universal adhesives has also improved efficiency. - **Material characteristics**: The materials used in the study include Tetric PowerFill and Tetric PowerFlow, designed for rapid curing, and control materials Filtek One Bulk Fill Restorative and SDR Plus Bulk Fill Flowable. ### Research Objectives: - **Evaluate the long-term effects of 3-second high-power curing on bond strength**: By comparing the bond strength of 3-second and 20-second curing methods after 1, 6, and 12 months, assess the feasibility and effectiveness of the rapid curing method. - **Determine the types of bonds formed by different materials**: By observing the fracture modes at the bonding interface, determine the types of fractures (adhesive, cohesive, or mixed). ### Conclusions: - **Effectiveness of 3-second curing**: Most materials showed comparable or higher bond strength under 3-second curing compared to 20-second curing, especially after 12 months. - **Material dependency**: Tetric PowerFill exhibited the best long-term performance under 3-second curing, while fluid materials (such as Tetric PowerFlow and SDR+) showed a decrease in bond strength after 12 months. - **Types of bonds**: Mainly adhesive fractures were observed, with no cohesive fractures found. Overall, this study provides important references for the application of rapid curing technology in dental restorations, especially for materials designed for rapid curing.