Abstract:The NASA InSight Lander on Mars includes the Heat Flow and Physical Properties Package HP3 to measure the surface heat flow of the planet. The package uses temperature sensors that would have been brought to the target depth of 3-5 m by a small penetrator, nicknamed the mole. The mole requiring friction on its hull to balance remaining recoil from its hammer mechanism did not penetrate to the targeted depth. Instead, by precessing about a point midway along its hull, it carved a 7 cm deep and 5-6 cm wide pit and reached a depth of initially 31 cm. The root cause of the failure - as was determined through an extensive, almost two years long campaign - was a lack of friction in an unexpectedly thick cohesive duricrust. During the campaign - described in detail in this paper - the mole penetrated further aided by friction applied using the scoop at the end of the robotic Instrument Deployment Arm and by direct support by the latter. The mole tip finally reached a depth of about 37 cm, bringing the mole back-end 1-2 cm below the surface. It reversed its downward motion twice during attempts to provide friction through pressure on the regolith instead of directly with the scoop to the mole hull. The penetration record of the mole was used to infer mechanical soil parameters such as the penetration resistance of the duricrust of 0.3-0.7 MPa and a penetration resistance of a deeper layer ( > 30 cm depth) of 4.9 ± 0.4 MPa . Using the mole's thermal sensors, thermal conductivity and diffusivity were measured. Applying cone penetration theory, the resistance of the duricrust was used to estimate a cohesion of the latter of 2-15 kPa depending on the internal friction angle of the duricrust. Pushing the scoop with its blade into the surface and chopping off a piece of duricrust provided another estimate of the cohesion of 5.8 kPa. The hammerings of the mole were recorded by the seismometer SEIS and the signals were used to derive P-wave and S-wave velocities representative of the topmost tens of cm of the regolith. Together with the density provided by a thermal conductivity and diffusivity measurement using the mole's thermal sensors, the elastic moduli were calculated from the seismic velocities. Using empirical correlations from terrestrial soil studies between the shear modulus and cohesion, the previous cohesion estimates were found to be consistent with the elastic moduli. The combined data were used to derive a model of the regolith that has an about 20 cm thick duricrust underneath a 1 cm thick unconsolidated layer of sand mixed with dust and above another 10 cm of unconsolidated sand. Underneath the latter, a layer more resistant to penetration and possibly containing debris from a small impact crater is inferred. The thermal conductivity increases from 14 mW/m K to 34 mW/m K through the 1 cm sand/dust layer, keeps the latter value in the duricrust and the sand layer underneath and then increases to 64 mW/m K in the sand/gravel layer below. Supplementary information: The online version contains supplementary material available at 10.1007/s11214-022-00941-z.

Mars Soil Temperature and Thermal Properties From InSight HP3 Data

Thermal Creep on Mars: Visualizing a Soil Layer under Tension

The InSight HP3 Penetrator (Mole) on Mars: Soil Properties Derived from the Penetration Attempts and Related Activities

The InSight HP$^3$ Penetrator (Mole) on Mars: Soil Properties Derived From the Penetration Attempts and Related Activities

The atmosphere of Mars as observed by InSight

The InSight HP$^3$ mole on Mars: Lessons learned from attempts to penetrate to depth in the Martian soil

The Mars Science Laboratory record of optical depth measurements via solar imaging

Thermal Vision for Soil Assessment in a Multipurpose Environmental Chamber under Martian Conditions towards Robot Navigation

Comparing Atmospheric Temperature Fluctuations Across Landed Missions

Near Surface Atmospheric Temperatures at Jezero from Mars 2020 MEDA measurements

Constraints on Lateral Variations of Martian Crustal Thickness From Seismological and Gravity Field Measurements

Thickness and structure of the martian crust from InSight seismic data

Relative Humidity on Mars: New Results From the Phoenix TECP Sensor

Constraints on the shallow elastic and anelastic structure of Mars from InSight seismic data

Spin state and deep interior structure of Mars from InSight radio tracking

Seasonal variations of snow depth on Mars

Diurnal variation of the surface temperature of Mars with the Emirates Mars Mission: A comparison with Curiosity and Perseverance rover measurements

Reconciling Mars InSight Results, Geoid, and Melt Evolution With 3D Spherical Models of Convection

Liquid water in the Martian mid-crust

Potential Effects of Atmospheric Collapse on Martian Heat Flow and Application to the InSight Measurements

Initial results from the InSight mission on Mars