Abstract:Aim: With modern dentistry advancements, children and parents have significantly raised aesthetic expectations in pediatric dentistry. Pediatric zirconia crowns (PZCs) provide a superior aesthetic appearance compared with stainless steel crowns (SSCs), making them a popular treatment option. However, a comparison of the compressive stresses caused by these crowns on the roots of primary teeth and alveolar bones has not been conducted. Materials and Methods: Cone beam computed tomography (CBCT) images of an eight-year-old female patient who experienced premature loss of a primary mandibular left second molar were obtained from a dental hospital database. Rhinoceros 4.0 software was used to process and simulate images. Under simulated chewing forces, stress on the PZC, SSC, and intact primary first molars as control groups, as well as their roots and alveolar bone structures, was assessed with finite element analysis. Statistical Analyses: Depending on whether the descriptive data were normally distributed, the Student t-test and Mann-Whitney U test were used. Quantitative variables differ between the two categories of qualitative variables. One-way ANOVA and Kruskal-Wallis H tests were used depending on standard distribution assumptions. p < 0.05 indicates statistical significance differences. Results: PZCs, SSCs, and cement layers were stressed according to von Mises values, while roots and alveolar bones were stressed according to maximum and minimum stress values. When assessing crowns, SSCs exhibited the highest von Mises stress values, followed by PZCs and control groups (p < 0.001). In the cement layer, SSCs obtained significantly higher values (p = 0.003). In the root area, minimum principal stress values are more critical. The highest values were obtained from the intact tooth, PZC, and SSC, respectively (p < 0.001). Alveolar bones did not differ significantly in minimum principal stress (p = 0.950). Conclusions: Restorative full-coverage crowns exhibited higher von Mises values than intact teeth, as per current research findings. The von Mises values were highest in SSC, while lowest in PZC. As a result of this condition, the cement layer and root areas had higher von Mises stress and compressive stress. Alveolar bones were not affected regardless of restoration type. PZC transmits higher stress due to its properties.

Stress Distribution in Proclined Anterior Teeth of Pediatric Patients With and Without Mouthguard Use: A 3D Finite Element Analysis

Stress Distribution Pattern of a Calculated Standardized Force on Maxillary and Mandibular Jaws with Proclined Maxillary Anterior Teeth with and without the Use of Mouthguard: A 3D Finite Element Analysis

Stress Concentration of Hybrid Occlusal Splint-Mouthguard during a Simulated Maxillofacial Traumatic Impact: 3D-FEA

Occlusal stress distribution in the human skull with permanent maxillary first molar extraction: A 3-dimensional finite element study

The effect of dental restoration geometry and material properties on biomechanical behaviour of a treated molar tooth: A 3D finite element analysis

Evaluation of stress distribution values at the temporomandibular joint and distalization of teeth during en-masse retraction of the mandibular dentition using buccal shelf bone screws: A FEM study

The mouthguard for sports is capable of protecting the implant/crown complex when there is a frontal impact? Responding with finite element analisys

Stress Distribution of Pediatric Zirconia and Stainless Steel Crowns after Pulpotomy Procedure under Vertical Loading: A Patient-Specific Finite Element Analysis

Biomechanical Behavior Evaluation of a Novel Hybrid Occlusal Splint-Mouthguard for Contact Sports: 3D-FEA

Study on Occlusion-induced Mechanical Force Distribution in Dental Pulp Using 3-D Modeling Based on Finite Element Analysis

Stress distribution of the modified clear twin-block aligner on the temporomandibular joint, alveolar bone and teeth: A finite element analysis

Evaluation of stresses and displacement in the craniofacial region as a reaction to bone-anchored maxillary protraction in conjugation with posterior bite plane and rapid maxillary expansion in patients with Class III malocclusion: A finite element analysis study

Three-dimensional finite element analysis of unilateral mastication in malocclusion cases using cone-beam computed tomography and a motion capture system

Occlusal Stress Distribution on the Mandibular First Premolar - FEM Analysis

Study of Protection Factors of Skull Base with Loaded Mandible

Stress distribution in the temporo-mandibular joint discs during jaw closing: a high-resolution three-dimensional finite-element model analysis

Occlusal load modelling significantly impacts the predicted tooth stress response during biting: a simulation study

Three-dimensional Finite Element Analysis of Influence of Occlusal Surface Height on Stress Distribution Around Posterior Implant-Supported Single Crown

Influence of occlusal contact and cusp inclination on the biomechanical character of a maxillary premolar: a finite element analysis.

Effect of several nickel-titanium rotary systems on stress distribution in mandibular molars under occlusal forces: a finite element analysis

Three-dimensional Finite Element Method Stress Analysis of First Mandibular Premolar with Various Degree of Wedge-shaped Defects under Loading