Abstract:Introduction The Biggest challenges coal-fired power plants are facing are improving their energy efficiencies and reducing their environmental impact due to CO2 and NOX emissions, can be attained by maximizing the steam pressure and temperature. However, the operating temperatures and pressures in boiler materials were restricted due to limited weldability of essential dissimilar joints between Austenitic Stainless Steel (ASS) and Creep-Enhanced Ferritic Steel (CEFS) due to carbon migration and sensitization. Present research work provides enhanced metallurgical and mechanical properties of weldment by optimizing the welding process and welding parameters. Aim The aim of the manuscript is to explores the welding compatibility of TP347H (stabilized ASS) with solution annealed T91 (CEFS), by Auto TIG welding technique, such that carbon migration at the fusion line of SA213 T91 and sensitization in the heat affected zone of TP347H can be minimized. Methods Influence of Auto TIG welding parameters on the mechanical, microstructure, and corrosion properties are studied and discussed. Carbon migration, mechanical and corrosion properties for lower (0.792 KJ/mm) and higher (1.124 KJ/mm) heat inputs weldments were compared. Investigation on mechanical properties test such as tensile, hardness, and root bend performed as per American Society of Mechanical Engineers (ASME) Section IX. Optical microscopy and Analytical Scanning Electron Microscope (SEM) coupled with Energy Dispersive Spectroscopy (EDS) have been performed to investigate carbon migration and sensitization behaviour. Sensitization susceptibility further validated by American Society for Testing and Materials (ASTM) A 262 Practice E. Results Investigation on tensile, hardness, and root bend tests revealed that mechanical properties for lower heat input weldment were superior. Restricted carbon migration due to optimized heat input improves mechanical properties and this was evidenced by satisfactory results of the bend test which showed no opening at the fusion line. A noticeable improvement in Ultimate Tensile Strength (UTS) 666 and 680N/mm2 (compared to 578 and 561N/mm2 for 1.124 KJ/mm heat input) and an acceptable hardness of 307 HV (compared to 399 HV for 1.124 KJ/mm heat input) were observed at T91 and weld metal interface. No fissures on bend surface and no Cr23C6 precipitation at grain boundary after performing ASTM A 262 Practice E and SEM-EDS respectively on heat affected zone (TP347H) of lower heat input weldment which shows higher resistance to intergranular corrosion (Sensitization). Conclusion Optimizing the welding parameters and decreasing the heat input mitigate the carbon migration at T91 fusion zone and, meeting the requirements for satisfactory mechanical properties in materials used for power generation applications. Further optimized welding heat input have lesser Cr23C6 precipitation in the heat-affected zone of TP347H, making the heat affected zone less susceptible to sensitization. Heat input must be controlled to (1) avoid intergranular corrosion failure or sensitization and (2) improve the mechanical properties of the weldment where requirement of post weld heat treatment is mandatory in the application (as recommended in the ASME Section 1, PW 39.1).

Influence of Induction Preheating and Post Weld Heat Treatment for Reducing Delta Ferrite Content and Improving Mechanical Properties of Induction Assisted Gas Metal Arc Welding of Modified 9Cr-1MoV Steel

Influence of Preheating and Post Heating on Diffusible Hydrogen Content, Residual Stresses and Hydrogen Assisted Cracking (HAC) Susceptibility of Induction Assisted Gas Metal Arc Welded P91 Steel Joint

Microstructure-Linked Mechanical Properties of P91-Incoloy 800HT Dissimilar Metal Welds

Carbon diffusion in dissimilar joints between P91 and 12Cr1MoV steels welded by different consumables at high temperature

Influence of Post-Weld Heat Treatment on Microstructural and Mechanical Properties of Dual-Phase Steel Gas Metal Arc-Welded Joints

Effect of Groove Design and Post-Weld Heat Treatment on Microstructure and Mechanical Properties of P91 Steel Weld

Effect of Induction Heat Treatment on Microstructure, Mechanical and Corrosion Properties of Stainless Steel 308L Fabricated Using Wire Arc Additive Manufacturing

Effect of Preheating Temperature on Retention of δ-Ferrite in ASTM A355 Grade P92

Residual stress analysis, microstructural characterization, and mechanical properties of tungsten inert gas-welded P92/AISI 304L dissimilar steel joints

Development and Evaluation of Dissimilar Gas Tungsten Arc-Welded Joint of P92 Steel/Inconel 617 Alloy for Advanced Ultra-Supercritical Boiler Applications

Postweld Heat Treatment of 15Cr-6Ni-2Mo-1Cu Supermartensitic Stainless Steel Welds

Autogenous laser-welded dissimilar joint of ferritic/martensitic P92 steel and Inconel 617 alloy: mechanism, microstructure, and mechanical properties

Study on Microstructural Characterization, Mechanical Properties and Residual Stress of GTAW Dissimilar Joints of P91 and P22 Steels

Influence of Ni and PWHT on microstructure evolution and mechanical properties of GTA-welded duplex stainless steel and super duplex stainless steel joints: A comparative investigation

Microstructure and Fatigue Behavior of Cr-Mo Steel Weld Joints with Automatic TIG Welding

A Study of Microstructure and Mechanical Properties for the Autogenous Single-Pass Butt Weldment of a Ferritic/Martensitic Steel Using Gas Tungsten Arc Welding

Mechanical and intergranular corrosion properties of auto TIG welded TP347H-T91 dissimilar weldments

Analyzing microstructural, residual stress, and mechanical characteristics in dissimilar welds of Inconel 59 and AISI 904L through double-pulsed gas metal arc welding

Enhanced Impact Toughness of Heat Affected Zone in Gas Shield Arc Weld Joint of Low‐C Medium‐Mn High Strength Steel by Post‐Weld Heat Treatment

Comparative evaluation of tensile properties of simulated heat affected zones of P91 steel weld joint

Induction Assisted Hybrid Friction Stir Welding of Dissimilar Materials AA5052 Aluminium Alloy and X12Cr13 Stainless Steel