Abstract:The use of soft robotic actuators is on the rise because these soft systems offer the advantage of being highly flexible, which affords safer robot-environment interactions and the gentleness necessary to handle delicate objects. However, this advantage becomes a shortcoming in high-force applications where flexible components fold and fail under large loads. Various methods were sought to meet this challenge by providing a level of rigidity to soft components, but previously proposed solutions bring their own drawbacks including bulky systems, addition of superfluous weight, and restriction of actuator motion. Alternatively, this article presents Tubular Jamming, a new and effective means of stiffening that is adaptable to motion, lightweight, and can be implemented with minimal equipment. In this study, the mechanism of tubular jamming is expounded and is demonstrated through two exemplary soft structures: a tubular jammed beam (TJB) and a tubular jammed hinge (TJH). Both TJB and TJH are exhibited in areas of fabrication, characterization, and a few possible examples of implementation in soft robotic systems. In the TJB structure, tubular jamming is found to increase bending stiffness by nearly threefold at the maximum pressure and packing ratio tested, compared with a traditional soft pneumatic actuator (SPA) beam. The TJB is shown to require less supply pressure to achieve the same performance as a traditional SPA and is shown to perform better in maintaining the vertical position of a borne object. A triangular support configuration made from TJBs is demonstrated to be proficient in weight bearing, supporting a load of nearly 33 times its own weight. In the TJH structure, tubular jamming is shown to have a compound effect on torque output, as three jammed tubule hinges produce approximately four times the torque of a single tubule hinge. The TJH is exhibited in a wearable elbow flexion device. Tubular jamming opens new possibilities for soft components to achieve the stiffness needed to perform high-force tasks such as weight bearing and large-scale actuation while retaining the suppleness to enable a safe robot-to-environment interface.

Stiffness Control of Laminar Jammers with Fused Layers: A Discrete Approach

Pump Up the Jam: Granular Media as a Quasi‐Hydraulic Fluid for Independent Control Over Isometric and Isotonic Actuation

Composite Laminar Jamming: Toward Designing a Tunable Stiffness Hybrid Soft Robotic Actuator

In Situ Stiffness Manipulation Using Elegant Curved Origami

A Review of Mechanisms to Vary the Stiffness of Laminar Jamming Structures and Their Applications in Robotics

Tubular Jamming: A Variable Stiffening Method Toward High-Force Applications with Soft Robotic Components

Fiber Jamming Transition as a Stiffening Mechanism for Soft Robotics

Chain-Like Granular Jamming: A Novel Stiffness-Programmable Mechanism for Soft Robotics

A 3D Printed Soft Robotic Gripper With a Variable Stiffness Enabled by a Novel Positive Pressure Layer Jamming Technology

Honeycomb Jamming: An Enabling Technology of Variable Stiffness Reconfiguration

Force Analysis And Experiment Of Variable Stiffness Soft Actuator Based On Particle Jamming

Variable stiffness performance analysis of layer jamming actuator based on bionic adhesive flaps

Dynamically Reprogrammable Stiffness in Gecko-Inspired Laminated Structures

Soft, Multi-DoF, Variable Stiffness Mechanism Using Layer Jamming for Wearable Robots

Controllable Stiffness Origami “skeletons” for Lightweight and Multifunctional Artificial Muscles

Muscle-inspired stiffness-tunable flexible fiber jamming structure for wearable robots

Stiffness Modulation for Soft Robot Joint Via Lattice Structure Configuration Design

Layer Jamming of Magnetorheological Elastomers for Variable Stiffness in Soft Robots

Controlled actuation, adhesion, and stiffness in soft robots: A review

Elasticity-Controlled Jamming Criticality in Soft Composite Solids

Tuning Stiffness with Granular Chain Structures for Versatile Soft Robots