Abstract:Abstract In deep underground mining, achieving stable support for roadways along with long service life is critical and the complex geological environment at such depths frequently presents a major challenge. Owing to the coupling action of multiple factors such as deep high stress, adjacent faults, cross-layer design, weak lithology, broken surrounding rock, variable cross-sections, wide sections up to 9.9 m, and clusters of nearby chambers, there was severe deformation and breakdown in the No. 10 intersection of the roadway of large-scale variable cross-section at the − 760 m level in the Nanfeng working area of the Wuyang Coal Mine. As there are insufficient examples in engineering methods pertaining to the geological environment described above, the numerical calculation model was oversimplified and support theory underdeveloped; therefore, it is imperative to develop an effective support system for the stability and sustenance of deep roadways. In this study, a quantitative analysis of the geological environment of the roadway through field observations, borehole peeking, and ground stress testing is carried out to establish the FLAC 3D variable cross-section crossing roadway model. This model is combined with the strain softening constitutive (surrounding rock) and Mohr-Coulomb constitutive (other deep rock formations) models to construct a compression arch mechanical model for deep soft rock, based on the quadratic parabolic Mohr criterion. An integrated control technology of bolting and grouting that is mainly composed of a high-strength hollow grouting cable bolt equipped with modified cement grouting materials and a high-elongation cable bolt is developed by analyzing the strengthening properties of the surrounding rock before and after bolting, based on the Heok-Brown criterion. As a result of on-site practice, the following conclusions are drawn: (1) The plastic zone of the roof of the cross roadway is approximately 6 m deep in this environment, the tectonic stress is nearly 30 MPa, and the surrounding rock is severely fractured. (2) The deformation of the roadway progressively increases from small to large cross-sections, almost doubling at the largest cross-section. The plastic zone is concentrated at the top plate and shoulder and decreases progressively from the two sides to the bottom corner. The range of stress concentration at the sides of the intersection roadway close to the passageway is wider and higher. (3) The 7 m-thick reinforced compression arch constructed under the strengthening support scheme has a bearing capacity enhanced by 1.8 to 2.3 times and increase in thickness of the bearing structure by 1.76 times as compared to the original scheme. (4) The increase in the mechanical parameters c and φ of the surrounding rock after anchoring causes a significant increase in σ c and σ t ; the pulling force of the cable bolt beneath the new grouting material is more than twice that of ordinary cement grout, and according to the test, the supporting stress field shows that the 7.24 m surrounding rock is compacted and strengthened in addition to providing a strong foundation for the bolt (cable). On-site monitoring shows that the 60-day convergence is less than 30 mm, indicating that the stability control of the roadway is successful.

Analysis of the Support Failure Mechanism Caused by Bolt Pre-Tightening Force Loss

Study on the Bolt-mesh-anchor Surrounding Mechanism of a Roadway in a Soft and Thick Rock Seam

Study on Pretightening Loss Effect of Bolt Support in Deep Soft Rock Roadway

Mechanical Behavior of Loose High-Strength Bolted Connections with Thin Sheet Steels

Test on shear behavior of less-tightened high-strength bolted connections

Stability Analysis of Support Anchor Bolt in the Process of Surrounding Rock Fracture Evolution

Multi-scale experimental study on the failure mechanism of high-strength bolts under highly mineralized environment

A Failure Mechanism of Supports in Weakly Cemented Soft Rock Roadways and the Synergistic Support Design

Failure Analysis of Intersections of Large-Scale Variable Cross-Section Roadways in Deep Soft Rock and Study of Integrated Control Technology of Bolting and Grouting

Stress Distribution Law of Full-Length Anchorage Bolt in Rectangular Roadway

Failure Characteristics and Stability Control of Bolt Support in Thick-Coal-Seam Roadway of Three Typical Coal Mines in China

Study on the anchorage mechanism and roof stability control technology of bolts in fractured or weak surrounding rock

Failure analysis and control technology of intersections of large-scale variable cross-section roadways in deep soft rock

Analysis of Bolt Mesh Support Failure in Soft Rock Roadway

Comparative Analysis of Roadway Reinforcement Effects Based on Fluid-Solid Coupling in the Fractured Zone of Water-Rich Fault

Failure Mechanism Analysis and Support Technology for Roadway Tunnel in Fault Fracture Zone: A Case Study

Deformation and failure characteristics of anchorage structure of surrounding rock in deep roadway

Study on Stability Control Mechanism of Deep Soft Rock Roadway and Active Support Technology of Bolt-Grouting Flexible Bolt

Research on the Stress Distribution Law of Fully Anchored Bolt and Analysis of Influencing Factors under the Condition of Surrounding Rock Deformation

Influence of anchorage length and pretension on the working resistance of rock bolt based on its tensile characteristics

The control effect of surrounding rock with different combinations of the bolt anchoring lengths and pre-tightening forces in underground engineering