Abstract:This study proposes a clustered dynamic adaptive chemistry (CDAC) method, which uses an iterative K-means algorithm to partition the computational cells into different groups according to their similarity in terms of the temperature and significant species compositions. Taking advantage of the clustered cells, the averaged thermo-chemical properties of the cells in the respective clusters are then used to identify the adaptive dynamic reduced chemistry through the method of direct relation graph with error propagation (DRGEP). Moreover, the integration of the chemical source term, which commonly dominates the computational effort in reactive flow simulations, is now performed using the dynamic adaptive reduced chemistry at the cluster level instead of the cell level. With this CDAC method, the on-the-fly DRGEP process as well as the chemistry integration only needs to be conducted at the cluster level, dramatically reducing the unnecessary repeated computation for similar computational cells. In addition, the adaptive dynamic reduced chemistry further accelerates the chemistry integration process due to less ordinary differential equations (ODEs) to be solved for each cluster. This newly proposed CDAC method was tested in multi-dimensional homogeneous charged compression ignition engine (HCCI), direct injection compression ignition (DICI) engine and constant volume chamber combustion (CVCC) fueled with diesel, biodiesel and kerosene through the use of their respective surrogate fuel mechanisms under different operating conditions. The performance of CDAC in terms of accuracy and efficiency were extensively analyzed and discussed using different user-defined parameters, mechanisms with different surrogate components and number of species as well as different meshes with different number of grid cells. Based on this analysis, the error tolerances in DRGEP and the error tolerances of the temperature and significant species' mass fraction are recommended as: epsilon(d) <= 0.001, epsilon(T) 20K and epsilon(Y) <= 0.01 to achieve less than 0.1% integral error. With these recommended user-defined tolerances, it can be observed that the current CDAC method is able to accurately predict the in-cylinder pressure as well as the species profile in HCCI, DICI and the flame lift-off length in CVCC when compared with the full chemistry calculations as well as the experimental results. Moreover, with the recommended user defined error tolerances and a chemical kinetic model of 112 species, this CDAC method is capable of achieving a computational time speed-up factor of more than 3 compared to the conventional DAC and of almost 5 compared to the full chemistry. Finally, the CDAC method coupled CFD was applied to simulate a diesel DICI engine under three different engine speeds with a detailed primary reference fuel (PRF) mechanism of more than 1000 species. The 3-D simulation could be finished in acceptable CPU time while being able to well capture the experimental in-cylinder pressure and heat release rate for all the three engine speeds. (C) 2018 The Combustion Institute. Published by Elsevier Inc. All rights reserved.

Applicability and Validity of CFD‐based Compartment Models for One to Multiple Operating Points

Computation of Flow Past an In-Line Oscillating Circular Cylinder and a Stationary Cylinder in Tandem Using a CIP-Based Model

COMPARTMENTAL MODELS FOR SEPARATION COLUMNS

An Automatic Method for Generation of CFD-Based 3D Compartment Models: Towards Real-Time Mixing Simulations

Advanced Modeling Approaches for CFD Simulations of Coal Combustion and Gasification

Computational Acceleration of Multi-Dimensional Reactive Flow Modelling Using Diesel/biodiesel/jet-Fuel Surrogate Mechanisms Via a Clustered Dynamic Adaptive Chemistry Method

Compartmental modeling and solving of large-scale distillation columns under variable operating conditions

Efficient Evaluation of Small Failure Probability in High-Dimensional Groundwater Contaminant Transport Modeling Via A Two-Stage Monte Carlo Method

Application and parameterization of a one‐dimensional multifluid population balance model to bubble columns

A conjugated heat and mass transfer model to implement reaction in particle-resolved CFD simulations of catalytic fixed bed reactors

Simulation of Bubble Column Reactors Using CFD Coupled with a Population Balance Model

State of the Art on Two-Phase Non-Miscible Liquid/Gas Flow Transport Analysis in Radial Centrifugal Pumps Part C: CFD Approaches with Emphasis on Improved Models

Advances in fixed-bed reactor modeling using particle-resolved computational fluid dynamics (CFD)

On the autonomous validation and comparison of particle models for a Newtonian laminar flow mixing model using PEPT

Advanced CFD modeling of rod bundle channels with integrated porous media and momentum source schemes

Experiment and multiphase CFD simulation of gas-solid flow in a CFB reactor at various operating conditions: Assessing the performance of 2D and 3D simulations

Multi-scale numerical simulation of fluidized beds: Model applicability assessment

Validation of computational fluid dynamics of shake flask experiments at moderate viscosity by liquid distributions and volumetric power inputs

Recurrence CFD - a novel approach to simulate multiphase flows with strongly separated time scales

CFD validation of condensation heat transfer in scaled-down small modular reactor applications, Part 1: Pure steam

Consistent Submodel Coupling in Hybrid Particle/finite Volume Algorithms for Zone-Adaptive Modelling of Turbulent Reactive Flows