Abstract:Bisphenol A dicyanate (BADCy) resin microparticles were prepared by precipitation polymerization synthesis and were homogeneously dispersed in a BADCy prepolymer matrix to prepare a BADCy self-reinforced composites. The active functional groups of the BADCy resin microparticles were characterized by Fourier transform infrared (FT-IR) spectroscopy. The results of an FT-IR curve showed that the BADCy resin microparticles had a triazine ring functional group and also had an active reactive group -OCN, which can initiate a reaction with the matrix. The structure of the BADCy resin microparticles was characterized by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). From the TEM results, the BADCy resin microparticles dispersed in the solvent were nano-sized and distributed at 40-60 nm. However, from the SEM results, agglomeration occurred after drying, the BADCy resin particels were micron-sized and distributed between 0.3 μm and 0.6 μm. The BADCy resin prepolymer was synthesized in our laboratory. A BADCy self-reinforced composite was prepared by using BADCy resin microparticles as a reinforcement phase. This corresponds to a composite in which the matrix and reinforcement phase are made from different morphologies of the same monomer. The DSC curve showed that the heat flow of the microparticles is different from the matrix during the curing reaction, this means the cured materials should be a microscopic two-phase structure. The added BADCy resin microparticles as reaction sites induced the formation of a more complete and regular cured polymer structure, optimizing the cross-linked network as well as increasing the interplay between the BADCy resin microparticles and prepolymer matrix. Relative to the neat BADCy resin material, the tensile strength, flexural strength, compressive strength and impact strength increased by 98.1%, 40.2%, 27.4%, and 85.4%, respectively. A particle toughening mechanism can be used to explain the improvement of toughness. The reduction in the dielectric constant showed that the cross-linked network of the self-reinforced composite was more symmetrical and less polar than the neat resin material, which supports the enhanced mechanical properties of the self-reinforced composite. In addition, the thermal behavior of the self-reinforced composite was characterized by thermogravimetric analysis (TGA) and dynamic mechanical thermal analysis (DMTA). The results of DMTA also establishes a basis for enhancing mechanical properties of the self-reinforced composite.

Self-extracted corn-stalk cellulose/epoxy resin composites

Adhesive Properties of Bio-Based Epoxy Resin Reinforced by Cellulose Nanocrystal Additives

Synthesis of Carboxymethyl Starch-Bio-Based Epoxy Resin and Their Impact on Mechanical Properties

Preparation and Characterization of Cellulose Fiber/chitosan Composites

Characterization of the Mechanical and Morphological Properties of Cow Dung Fiber-Reinforced Polymer Composites: A Comparative Study with Corn Stalk Fiber Composites and Sisal Fiber Composites

Synergistic impact of cellulose nanocrystals and calcium sulfate fillers on adhesion behavior of epoxy resin

Microcrystalline Cellulose As Reactive Reinforcing Fillers for Epoxidized Soybean Oil Polymer Composites

Role of silica-based porous cellulose nanocrystals in improving water absorption and mechanical properties

Nanostructure and interfacial mechanical properties of PEG/cellulose nanocomposites studied with molecular dynamics

Enhanced mechanical properties of epoxy composites using cellulose micro‐ and nano‐crystals

Development of silane-treated corn husk fiber and agro-waste biofiller-reinforced epoxy composite: effects on wear, mechanical, thermal, and water absorption properties

Characterization of natural cellulose fiber from corn stalk waste subjected to different surface treatments

Surface Modification of Cellulose Microcrystalline with Aluminate Coupling Agent and Its Effects on Flame Retardant and Mechanical Properties of Epoxy Resin

Enhancing Toughness, Healing and Reprocessability of Sustainable Epoxy Vitrimer Composites by PEG-assisted Regenerated Cellulose

Study on the Relationships between Microscopic Cross-Linked Network Structure and Properties of Cyanate Ester Self-Reinforced Composites

Aqueous Dispersion of Carbon Fibers and Expanded Graphite Stabilized from the Addition of Cellulose Nanocrystals to Produce Highly Conductive Cellulose Composites

Preparation and Characteristics of Biocomposites Based on Steam Exploded Sisal Fiber Modified with Amphipathic Epoxidized Soybean Oil Resin.

Experiment and molecular dynamics simulation of functionalized cellulose nanocrystals as reinforcement in cement composites

A novel biobased resin-epoxidized soybean oil modified cyanate ester

Extraction of Cellulose from Soybean Hulls for the Development of Polymer Matrix Composites with Fishtail Palm Fibers

Synergistic utilization of cold caustic extraction and deep eutectic solvent for the production of dissolving pulp from corn stalks