Abstract:In this study, the structure, electrical and thermal properties of ten polymer compositions based on polylactic acid (PLA), low-cost industrial graphene nanoplates (GNP) and multi-walled carbon nanotubes (MWCNT) in mono-filler PLA/MWCNT and PLA/GNP systems with 0–6 wt.% filler content were investigated. Filler dispersion was further improved by combining these two carbon nanofillers with different geometric shapes and aspect ratios in hybrid bi-filler nanocomposites. Scanning electron microscopy (SEM), transmission electron microscopy (TEM) and Raman spectroscopy exhibited uniform dispersion of nanoparticles in a polymer matrix. The obtained results have shown that for the mono-filler systems with MWCNT or GNP, the electrical conductivity increased with decades. Moreover, a small synergistic effect was observed in the GNP/MWCNT/PLA bi-filler hybrid composites when combining GNP and CNT at a ratio of 3% GNP/3% CNT and 1.5% GNP:4.5% CNT, showing higher electrical conductivity with respect to the systems incorporating individual CNTs and GNPs at the same overall filler concentration. This improvement was attributed to the interaction between CNTs and GNPs limiting GNP aggregation and bridging adjacent graphene platelets thus, forming a more efficient network. Thermal conductivity increases with higher filler content; this effect was more pronounced for the mono-filler composites based on PLA and GNP due to the ability of graphene to better transfer the heat. Morphological analysis carried out by electron microscopy (SEM, TEM) and Raman indicated that the nanocomposites present smaller and more homogeneous filler aggregates. The well-dispersed nanofillers also lead to a microstructure which is able to better enhance the electron and heat transfer and maximize the electrical and thermal properties. The obtained composites are suitable for the production of a multifunctional filament with improved electrical and thermal properties for different fused deposition modelling (FDM) 3D printing applications and also present a low production cost, which could potentially increase the competitiveness of this promising market niche.

Investigating Conductive Polymer Composites Developed Using Acrylonitrile Butadiene Styrene/Graphene/Multi-walled Carbon Nanotubes for Effective Thermal Management

Fabrication of Three-dimensional Thermally Conductive Carbon Fibers/Carbon Nanotubes Network Reinforce Epoxy Composites

Mechanical and Electrical Properties and Electromagnetic-Wave-Shielding Effectiveness of Graphene-Nanoplatelet-Reinforced Acrylonitrile Butadiene Styrene Nanocomposites

Experimental Study on Influence of Multiwalled Carbon Nanotubes on Thermal Behavior of ABS & PETG Hybrid Polymer Composites

Electrical Conductivity and Thermal Properties of Acrylonitrile‐butadiene‐styrene Filled with Multiwall Carbon Nanotubes

Investigation of electrical, electromagnetic interference shielding and tensile properties of 3D-printed acrylonitrile butadiene styrene/carbon nanotube composites

Acronitrile butadiene styrene/polycaprolactam/nano carbon black composites: Selective percolation, glass transition and temperature dependence of electrical conductivity

Preparation and Properties of ABS/BNNS Composites with High Thermal Conductivity for FDM

Modification of Thermal Conductivity of PMMA and PC by making their Nanocomposites with Carbon Nanotubes

Enhanced Mechanical, Thermal and Flame Retardant Properties by Combining Graphene Nanosheets and Metal Hydroxide Nanorods for Acrylonitrile–Butadiene–Styrene Copolymer Composite

Thermally Conductive 3D-Printed Carbon-Nanotube-Filled Polymer Nanocomposites for Scalable Thermal Management

Influence of amine surface treatments of carbon nanotube and boron nitride hybrid fillers on the thermal and mechanical properties of flexible amine‐based acrylate composites via 3D vat photopolymerization

Thermal conductive nylon 6 composites using hybrid fillers to construct a three‐dimensional thermal conductive network

Facile and scalable fabrication of highly thermal conductive polyethylene/graphene nanocomposites by combining solid-state shear milling and FDM 3D-printing aligning methods

3D Printing Processability of a Thermally Conductive Compound Based on Carbon Nanofiller-Modified Thermoplastic Polyamide 12

Thermal conductive segregated multi-scale network constructed by ball-milling and in-situ polymerization in PEEK/MWCNT/graphite composite

Influence of Extrusion Screw Speed and CNT Concentration on the Mechanical and EMI Properties of PC/ABS Based Nanocomposites

Enhanced thermal conductivity of polyamide nanocomposites involving expanded graphite–carbon nanotube network structure using supercritical CO2

A Trade-off Study Toward Highly Thermally Conductive and Mechanically Robust Thermoplastic Composites by Injection Moulding

MWCNTs-GNPs Reinforced TPU Composites with Thermal and Electrical Conductivity: Low-Temperature Controlled DIW Forming

PLA/Graphene/MWCNT Composites with Improved Electrical and Thermal Properties Suitable for FDM 3D Printing Applications