Abstract:Advanced Li-ion batteries adopting new cathode chemistries are required for the successful widespread transition to electric vehicles (EVs) and renewable energy sources, aiming for high energy density, long cycle life, and good rate capability. Commercial candidates for EV batteries include Ni-rich Li(Ni x Mn y Co 1−x-y )O 2 (NMC) cathodes, with Ni:Mn:Co ratios of 8:1:1 (NMC811) and higher. These are favored because of their high specific capacity (~ 200 mAh g -1 )and reduced cobalt content. Despite all of the advantages, these materials suffer from a range of degradation modes, many of which are associated with the redox and crystallographic behavior at high states of charge. In particular, Ni-rich cathodes suffer from several limitations, such as rapid capacity fade in comparison to NMC stoichiometries with lower Ni content. In addition, they also have a lower onset voltage for oxygen release and subsequent surface reconstruction leading to the formation of spinel and rock salt phases which impede (de)lithiation and therefore the achievable capacity of the cell. 1 Crystallographic properties of electrode materials are intrinsically linked to the electrochemical performance of the cell. NMC materials suffer from anisotropic changes in the crystal structure during cycling which induces strain and leads to issues such as crack formation, expediting degradation. One method to tackle capacity fade is to switch to single-crystal morphologies (particle size 1-3 μm) which have better mechanical stability than conventional polycrystalline morphologies (secondary agglomerate particles ~ 10 μm made up of primary particles which are 100 nm – 1 μm in size) and have less propensity to form extensive rock-salt layers. It is thought that the single-crystal morphology helps to reduce stress in the material as the anisotropic stress in polycrystalline cathodes is concentrated at grain boundaries. However, there is still a limited understanding of the subtle mechanistic differences between the two materials during cycling. 2 A multi-scale approach is required to gain a more comprehensive understanding of the degradation mechanisms at play and how they initiate and propagate. In this work, synchrotron diffraction methods were employed at the crystal, particle and cell scale using a variety of techniques including in-situ Bragg Coherent Diffraction Imaging (BCDI), 3D-XRD and operando high-resolution XRD. Intra-particle, inter-particle and electrode level heterogeneities were observed during cycling, both in pristine and aged samples. It is believed that these heterogeneities accelerate the loss of performance at the cell level by inducing crack formation which can then be observed in X-ray computed tomography data acquired in simultaneous lab studies. The overarching goal of these investigations is to add to the understanding of complex degradation mechanisms for Ni-rich layered transition metal oxide cathodes, ultimately aiding in the informed development of future battery electrode materials. References: 1] Xu, C. et al., Phase Behaviour during Electrochemical Cycling of Ni‐Rich Cathode Materials for Li‐Ion Batteries. Adv. Energy Mater. 2021, 11, 2003404. 2] Yin, S. et al., Fundamental and solutions of microcracks in Ni-rich layered oxide cathode materials of lithium-ion batteries. Nano Energy, 2021, 83, 105854.

Degradation by Kinking in Layered Cathode Materials

Unravelling the Impact of Reaction Paths on Mechanical Degradation of Intercalation Cathodes for Lithium-Ion Batteries.

Bulk and surface degradation in layered Ni-rich cathode for Li ions batteries: Defect proliferation via chain reaction mechanism

Origin of structural degradation in Li-rich layered oxide cathode

New Insight into Bulk Structural Degradation of High-Voltage LiCoO2 at 4.55 V.

Understanding the Degradation Mechanisms of Lithium Ion Batteries Using in-Situ Multi-Scale Diffraction Techniques

Mitigating Anisotropic Changes in Classical Layered Oxide Materials by Controlled Twin Boundary Defects for Long Cycle Life Li-Ion Batteries

Native lattice strain induced structural earthquake in sodium layered oxide cathodes

Direct Observation Of Defect-Aided Structural Evolution In A Nickel-Rich Layered Cathode

High‐Voltage Charging‐Induced Strain, Heterogeneity, and Micro‐Cracks in Secondary Particles of a Nickel‐Rich Layered Cathode Material

Origins and Importance of Intragranular Cracking in Layered Lithium Transition Metal Oxide Cathodes

Degradation of Layered Oxide Cathode in a Sodium Battery: A Detailed Investigation by X-Ray Tomography at the Nanoscale

New Insight into Bulk Structural Degradation of High-Voltage LiCoO 2 at 4.55 V

Threshold for degradation

Operando chemo-mechanical evolution in LiNi0.8Co0.1Mn0.1O2 cathodes

Reaction inhomogeneity coupling with metal rearrangement triggers electrochemical degradation in lithium-rich layered cathode

Heterogeneous Degradation in Thick Nickel‐Rich Cathodes During High‐Temperature Storage and Mitigation of Thermal Instability by Regulating Cationic Disordering

Electrochemomechanical failure in layered oxide cathodes caused by rotational stacking faults

Role of surface modification on high-voltage phase transition and degradation of layered P2-Na2/3Ni1/3Mn2/3O2 cathode material for Na-ion batteries

Effects of Bending on Nucleation and Injection of Oxygen Vacancies into the Bulk Lattice of Li‐Rich Layered Cathodes

Theoretical Understanding and Experimental Suppression of the Capacity Degradation of Ni-Rich Layered Oxide Cathode Materials for Li Ion Battery