Abstract:Coating boron particles with materials having multiple mechanisms of action is a promising way to promote the ignition and combustion properties of boron. The differences in thermal oxidation properties and ignition combustion characteristics of micron-sized boron composite particles (namely, AP@B, FR@B, and GAP@B) coated with 20 wt% ammonium perchlorate (AP), fluoropolymer (FR), or glycidyl azide polymer (GAP) were comparatively investigated using TG-DSC and CO2 laser ignition test systems. The results showed that the starting reaction temperature and activation energy of the composite particles were significantly reduced by the lower pyrolysis temperatures of the three modified materials. However, their oxidation phase lagged behind that of the original boron particles, most likely because the coating agglomerated 27% of the fine boron particles ( < 0.1 mu m) into micron-sized particles. In addition, the slow heating approach did not allow the particles to reach the ignition temperature immediately and may indirectly aggravate the oxide layer thickness. Nevertheless, the coating modifier effectively promoted energy release (the heat release was increased by 93.76%, 28.65%, and 24.20% for FR@B, GAP@B, and AP@B, respectively). Generally, the ignition delay time (t(i)) decreases, whereas the combustion time (t(c)), selfsustaining combustion time (t(f)), maximum combustion temperature (T-max) and burnout rate (alpha) increase after the coating of modified materials. First, AP decomposition produced O-2 and other gases to provide an oxidant for boron combustion and disperse the particles into space, which promotes extremely rapid energy release. Thus, the T-max and alpha of AP@B were significantly enhanced. Second, FR pyrolysis gas production can vaporize B2O3 and then promote the exposure of internal boron to react with oxygen. Thus, the t(f) and alpha of FR@B were significantly enhanced. However, the T-max value was not the highest since the highest calorific value (up to 15,094 J.g(-1)) of FR@B is released at a slow rate. Finally, GAP can significantly shorten ti due to its lower activation energy, and this modification effect can be significantly improved by increasing the O-2 content. Since boron is characterized by high oxygen consumption, increasing the oxygen partial pressure can significantly promote ignition and combustion. The T-max values of four samples in a mixed O-2 -N-2 environment under 1.0 MPa even exceeded the boiling point of B2O3, which is favorable for the reaction of internal boron with oxygen due to the gasification of the oxide layer at this time. (C) 2022 The Combustion Institute. Published by Elsevier Inc. All rights reserved.

Preparation and properties of nano B/NC/AP@F 2602 double-layer energetic fiber

Electrospun Nano-boron–Ammonium Dinitramide Core–sheath Nanofibers

Combustion Characteristics and Performance of Nanoflower Structure AlB2@AP Energetic Composites

Preparation, characterization, and combustion properties of NGO/GF/B composite system

Boron Nanocrystals As High-Energy-density Fuels

Energetic Properties of Core–shell B@PVDF/AP Composite Micro-Units Prepared by Electrostatic Spraying Technology

Encapsulated boron-based energetic spherical composites with improved reaction efficiency and combustion performance

Boron/Difluoroamino (B/NF2) Composites Prepared Through an Energetic Fluorinated-Centerd Surface Modification Strategy to Enhance Their Ignition and Combustion Characteristics

Dual-core-shell structure B@LiF@AP with multi-effect synergies to improve processibility and energy release characteristics of B

Preparation and Properties of Boron‐Based Nano‐B/NiO Thermite

The surface activation of boron to improve ignition and combustion characteristic

Facile method constructed naphthalene and Cu-C/Ni-C modified amorphous boron with high ignition and combustion performances

A Promising Strategy to Obtain High Energy Output and Combustion Properties by Self-Activation of Nano-Al

Carbon Nanofibers Introduce Nitroguanidine Propulsion to Improve Mechanical Properties, and the Study of Thermal Decomposition, Combustion Behavior and Molecular Dynamics

Preparation and Characterisation of the NBC/CL-20/AP Nanoenergetic Composite Materials

Ignition and Combustion of Boron Particles Coated by Modified Materials with Various Action Mechanisms

Construction of boron-based double-layer core-shell structure composites and their combustion energy release characteristics

Atomistic Insights into Two-Stage Combustion of a Single Boron Nanoparticle Via Reactive Molecular Dynamics

The combustion behavior of boron particles by using molecular perovskite energetic materials as high-energy oxidants

Boron-based composite energetic materials (B-CEMs): Preparation, combustion and applications

Promoting the Combustion Properties of Boron Powder Through In‐situ Coating