Abstract:Geopolymers, as a novel cementitious material, exhibit typical brittle failure characteristics under stress. To mitigate this brittleness, fibers can be incorporated to enhance toughness. This study investigates the effects of varying polypropylene fiber (PPF) content and fiber length on the flowability, mechanical properties, and flexural toughness of coal gangue-based geopolymers. Microstructural changes and porosity variations within the Fiber-Reinforced Geopolymer Mortar(GMPF) matrix were observed using scanning electron microscope (SEM) and Low field NMR(LF-NMR) to elucidate the toughening mechanism of PPF-reinforced geopolymers. The introduction of fibers into the geopolymer matrix demonstrated an initial bridging effect in the viscous geopolymer slurry, with a 3.0 vol% fiber content reducing fluidity by 5.6%. Early mechanical properties of GMPF were enhanced with fiber addition; at 1.5 vol% fiber content and 15 mm length, the 3-day flexural and compressive strengths increased by 30.81% and 17.4%, respectively. Furthermore, polypropylene fibers significantly improved the matrix's flexural toughness, which showed an increasing trend with higher fiber content. At a 3.0 vol% fiber content, the flexural toughness index increased by 198.35%. The data indicated that a fiber length of 12 mm yielded the best toughening effect, with an 84.03% increase in the flexural toughness index. SEM observations revealed a strong interfacial bond between fibers and the matrix, with noticeable damage on the fiber surface due to frictional forces, and fiber pull-out being the predominant failure mode. Porosity testing results indicated that fiber incorporation substantially improved the internal pore structure of the matrix, reducing the median pore diameter of mesopores and converting mesopores to micropores. Additionally, the number of harmless and less harmful pores increased by 23.01%, while the number of more harmful pores decreased by 30.43%.

Fracture performance and damage behavior of fly ash-based geopolymers toughened by molybdenum tailings based on acoustic emission and digital image correlation

Research on the early fracture behavior of fly ash-based geopolymers modified by molybdenum tailings

Residual water and interfacial bonding effects on the mechanical performance of CNT/fly ash geopolymer binder

Effects of High Temperature and Substitution Rates of Fly Ash on the Mechanical Properties and Microstructures of Steel-Basalt Hybrid Fibers Reinforced Cementitious Composites

Experimental Study on the Flexural Fatigue Performance of Slag/fly Ash Geopolymer Concrete Reinforced with Modified Basalt and PVA Hybrid Fibers

The Long-Term Leaching Behavior of Heavy Metals in Geopolymers and Portland Cement Bricks Containing Mswi Fly Ash: A Comparative Study

Physical and mechanical properties and micro characteristics of fly ash-based geopolymer paste incorporated with waste Granulated Blast Furnace Slag (GBFS) and functionalized Multi-Walled Carbon Nanotubes (MWCNTs)

Effect of Waste Glass Powder and Bamboo Fiber on the Physico-Mechanical Properties and High-Temperature Behavior of a Fly Ash-Based Geopolymer

Development of Low-Calcium Fly Ash-Based Geopolymer Mortar Using Nanosilica and Hybrid Fibers

Properties of Fiber-Reinforced Geopolymer Mortar Using Coal Gangue and Aeolian Sand

Synthesis of one-part geopolymers from alkaline-activated molybdenum tailings: Mechanical properties and microstructural evolution

Fracture Properties and Softening Curves of Steel Fiber-Reinforced Slag-Based Geopolymer Mortar and Concrete

Study on the high-temperature resistance of metakaolin-fly ash-based geopolymers

Fracture Mechanical Properties of Steel Fiber Reinforced Self-Compacting Concrete under Dry–Wet Cycle Sulfate Attack

Study on Fabrication and Microstructures of Fly Ash Based Geopolymeric Cements

Correlation of Microstructural and Mechanical Properties of Geopolymers Produced from Fly Ash and Slag at Room Temperature

Performance deterioration of municipal solid waste incineration fly ash-based geopolymer under sulfuric acid attack

Effects of Spodumene Flotation Tailings on Mechanical Properties of Acid-Based Geopolymer Mortar

Mechanical Properties and Microstructural Features of Biomass Fly Ash-Modified Self-Compacting Coal Gangue-Filled Backfill

High temperature resistance of fly ash/GGBFS-based geopolymer mortar with load-induced damage

Effect of multi-walled carbon nanotubes on durability of high-strength slag-based geopolymer