Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

Interfacial processes underlying the temperature-dependence of friction and wear of calcite single crystals

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

The Effects of Humidity on the Velocity-Dependence and Frictional Ageing of Nanoscale Silica Contacts

Velocity and Temperature Dependence of Steady‐State Friction of Natural Gouge Controlled by Competing Healing Mechanisms

Nanoscale friction at the quartz-quartz/kaolinite interface

Effect of humidity on granular friction at room temperature

Surface Forces Apparatus Measurements of Interactions between Rough and Reactive Calcite Surfaces

Mechanical Energy Dissipation During Seismic Dynamic Weakening in Calcite‐Bearing Faults

Contact size effects on the friction and wear of amorphous carbon films

Mechanical Properties of Single-Crystal Calcite and Their Temperature and Strain-Rate Effects

Load-velocity-temperature relationship in frictional response of microscopic contacts

Effect of wear particles and roughness on nanoscale friction

Atomic-scale Interfacial Instability of Hydrogenated Amorphous Carbon Film at Elevated Temperature

Investigation of friction behavior between tire and pavement by molecular dynamics simulations

Dependence of Simulated Fault Gouge Frictional Behavior on Mineral Surface Chemistry Quantified by Cation Exchange Capacity

The effect of high temperature and pressure on rock friction coefficient: a review

A story of two transitions: From adhesive to abrasive wear and from ductile to brittle regime

Unraveling Tribochemistry and Self-Lubrication Mechanism of Polytetrafluoroethylene by Reactive Coarse-Grained Molecular Dynamics Simulations.

Roughness evolution induced by third-body wear

Peak Effect versus Skating in High Temperature Nanofriction

Temperature dependence of energy dissipation during nanoscale wear of AISI 304L stainless steel