Abstract:In order to verify the feasibility of three-dimensional (3D) printing technology in preparing the metamaterial absorbers with complex structure, a three-layer broadband absorbing metamaterial is designed and fabricated by 3D printing technology. The surface layer and middle layer of the metamaterial are composed of periodic arrays with different unit dimensions and the bottom layer of a slab structure. The optimized thickness of the metamaterial is 4.7 mm. A composite absorbent which consists of carbonyl iron powder and nylon is used to fabricate the absorber. In experiment, the obtained absorber is vertically irradiated by an electromagnetic (EM) wave. Two strong absorption peaks at 5.3 GHz and 14.1 GHz are achieved, with the reflection losses of -15.1 dB and -12.5 dB, respectively. The superposition of the two absorption peaks results in a reflection loss below -10 dB in a range from 4 to 18 GHz. The effective EM parameters of the surface layer and the middle layer are calculated by the S parameter inversion method. An effective model of the three-layer structure absorber is proposed and its reflectivity is calculated by using a multilayer structure reflectivity formula. The calculated reflectivity agrees well with the measured one. The absorbing and resonance mechanisms of the two absorption peaks are investigated by analyzing the dynamic distributions of power density loss, electric field and magnetic field. It can be clearly confirmed that the reflection losses at 5.3 GHz and 14.1 GHz are primarily concentrated on the bottom layer and surface layer, and the broadband absorption performance can be derived from the superposition of broadband absorptions of the three absorbing layers. Meanwhile, the strong electric coupling effect between the adjacent units in the surface layer is demonstrated by analyzing the electric-field distributions, which indicates that the strong reflection loss at 14.1 GHz is mainly caused by the electric response. The multiple scattering effects among the three layers are also considered according to the magnetic field distributions at two resonance frequencies. It is shown that there are two magnetic responses at 5.3 GHz and 14.1 GHz, respectively, and the multiple scattering contributes to increasing the EM wave propagation distance and enhancing the power loss. The designed absorbing metamaterials in this paper achieve good broadband absorption performances, particularly in the low frequency band. Combined with 3D printing rapid technology, a promising route to constructing 3D absorbing metamaterials with complex structures is proposed, which would be of great significance and broad practical prospect.

3D-printed broadband electromagnetic wave-absorbing basalt/CF/PLA composites with a high current path for lightning strike protection

3D Printed Nickel-Plated Carbon Fiber Mesh for Lightning Strike Protection

Influence of Impact on Electromagnetic Response of Three-Dimensional Angle-Interlock Metacomposites

3D-Printed Pyramid Broadband Absorber Using Carbon Black / Polypropylene Composite

Joule Heating Synthesis of Carbon Fiber/graphene 3D Crosslinked Structure for Lightning Strike Protection and Electromagnetic Interference in Aerospace Composites

Broad bandwidth of thin composite radar absorbing structures embedded with frequency selective surfaces

3D printing of carbon fiber powder/polylactic acid with enhanced electromagnetic interference shielding

Dual conductive network of nickel‐coated carbon fiber woven fabric for indirect and direct lightning strike protection of carbon fiber reinforced polymer composites

3D Printing and Characterization of Metamaterial Composite Structures for Absorbing and Shielding Electromagnetic Waves

Advanced lightweight lightning strike protection composites based on super-aligned carbon nanotube films and thermal-resistant zirconia fibers

A Double-Layered Composite for Lightning Strike Protection Via Conductive and Thermal Protection

Design on the Microwave Absorber with Lattice of 3D Composite Element for X-band Application

Vertical z-axis discontinuous carbon fibers for improved lightning strike performance of continuous fiber-reinforced polymer composites

Study of Carbon Nanotubes/short Carbon Fiber Nanocomposites for Lightning Strike Protection

Development of electrically conductive structural BMI based CFRPs for lightning strike protection

Three-Dimensional-Printed Carbon Nanotube/Polylactic Acid Composite for Efficient Electromagnetic Interference Shielding

Design and verification of the square convex surface multilayer radar absorbing structure based on additive manufacturing

Broadband Absorption Performance of 3D-Printed Polyetheretherketone-Based Electromagnetic Wave-Absorbing Composites

Fabrication of the Silver Modified Carbon Nanotube Film/carbon Fiber Reinforced Polymer Composite for the Lightning Strike Protection Application

Lightning strike damage behavior of zirconium carbide and copper modified short-carbon-fiber-reinforced boron phenolic resin composites under 200 kA

Structural Broadband Absorbing Metamaterial Based on Three-Dimensional Printing Technology