Abstract:The utilization of near-infrared lasers (approximately 1000 nm wavelength) on non-ferrous metals often presents challenges like unstable weld pools, suboptimal weld formation, and reduced mechanical performance due to high reflectivity. This investigation focused on dissimilar Cu/Ti materials undergoing coaxial welding with a near-infrared fiber laser (λ = 1080 nm) and a blue diode laser (λ = 455 nm) at various power ratios. The study centered on analyzing molten pool characteristics, microstructure, and mechanical properties of weld. The combination 1080/455 nm wavelength of lasers expanded the heating range along the weld seam, enhancing Keyhole stability and dynamic stability of molten pool. Increasing the power ratio of the 455 nm wavelength laser reduced temperature gradients in the molten pool, resulting in superior-quality joint with a maximum tensile strength of 245.93 MPa, surpassing that of the Cu base material. Interface analysis revealed that, while there was no significant variance in the phase composition of the Ti-side, augmenting the power ratio of the 455 nm wavelength laser increased post-heating during welding process, reducing low-angle grain boundaries in the Ti-side fusion zone from 58.3 % to 48.3 %. This enhanced distribution patterns for low-angle grain boundaries and geometrically necessary dislocations, optimizing stress distribution. The absorption of 455 nm wavelength laser energy by Cu results in molten pools that spread towards the Cu-side regions. This process causes a change in composition from TiCu2 to TiCu4 in the fusion area, aided by exceptional thermal conductivity, resulting in increased cooling rates and undercooling levels. This grain refinement improved resistance against dislocation generation, enhancing strength and plasticity. This study demonstrates the feasibility of achieving high-quality welding between Cu/Ti dissimilar materials using a coaxial hybrid beam with a wavelength of λ = 1080/455 nm, offering an innovative solution for laser welding of highly reflective materials.

Study on weld formation and segregation mechanism for dissimilar pulse laser welding of NiTi and Cu wires

Study on laser welding of Cu/Ti dissimilar materials using a hybrid light source with wavelengths of 455/1080 nm

The Microstructures and Mechanical Properties of Dissimilar Laser Welding of Copper and 316L Stainless Steel with Ni Interlayer

Characterization of laser beam offset welding TiNi alloy and 304 stainless steel with different joining modes

Microstructure Characteristics and Mechanical Properties of γ-TiAl/Steel Joints with Different Laser Pulse Currents

Study on Laser Overlap Welding of Titanium/Aluminum Dissimilar Metals Based on Niobium Microalloying

Microstructure and Tensile Behavior of Laser Arc Hybrid Welded Dissimilar Al and Ti Alloys

Effect of various interlayers in NiTi to TC4 dissimilar joints by magnetic pulse welding

High-Strength Dissimilar Welds Between a NiTi Shape Memory Alloy and Titanium Obtained by Intermixing Niobium Using Pulsed Laser Beam Welding

Effect of single alloying element (Ti, Nb, V, Cu) on microstructure and mechanical properties of dissimilar TiAl/Ni-based superalloy laser joints

Microstructure and mechanical property of Ti/Cu ultra-thin foil lapped joints with different weld depths by nanosecond laser welding

Experimental and numerical study on microstructure and mechanical properties for laser welding-brazing of TC4 Titanium alloy and 304 stainless steel with Cu-base filler metal

Microstructure, Macrosegregation, and Mechanical Properties of NiTi to Ti6Al4V Dissimilar Laser Welds Using Co Interlayer

Microstructure and Mechanical Properties of Fe-36Ni and 304L Dissimilar Alloy Lap Joints by Pulsed Gas Tungsten Arc Welding

Dissimilar welding between Cu–6Al–2Ni alloy and stainless steel 316L using continuous ytterbium YAG laser

Effect of different pulse shapes on the laser welding of aluminum and copper

Dissimilar Laser Welding of a NiTi Shape Memory Alloy to Ti2AlNb

Effects of heat source arrangements on Laser-MAG hybrid welding characteristics and defect formation mechanism of 10CrNi3MoV steel

Tensile resistance, microstructures of intermetallic compounds, and fracture modes of welded steel/aluminum joints produced using laser lap welding

Study on interface and mechanical property of laser welding of NiTi shape memory alloy and 2A12 aluminum alloy joint with a TC4 wire

Effect of pulse frequency on the nanosecond pulsed laser welded Al/steel lapped joint