Abstract:Maximizing the electrode thickness is an inevitable target to reach when improving the energy density of Li-ion batteries [1,2]. Unfortunately, the fabrication of electrodes of several hundreds of micrometer thickness is often accompanied by detrimental side-effects. A critical process step in thick electrode production is the drying of the coated layer. During the evaporation of the solvent, light components of the slurry such as binder and carbon black can be dragged to the top of the coating [3,4]. The lack of liquid linkage throughout the layer leads to binder particles being evenly spread across the coating after the drying process is concluded. Inhomogeneous distribution of binder can not only cause delamination, but also negatively influences the Li-ion transport pathways through the electrode. To ensure ideal mechanical stability and satisfactory electrochemical performance, binder migration needs to be suppressed effectively. Multi-layering has proven itself as a technique within aqueous processing to overcome the limitations arising for thick electrodes. Subsequent coating of layers offers opportunities to establish selective material compositions at specific regions within the electrode (Figure 1a). This novel coating method can be considered a steppingstone to further optimize high loading electrodes. We have previously demonstrated that by multi-layering an increase of 40% in adhesion can be achieved compared to single-layer electrodes. Moreover, the assembled cells show superior performances at rate capability tests. Especially for low current densities (0.2C) an increase of up to 20% in specific discharge capacity was reached through multi-layering (Figure 1b) [5]. Within aqueous electrode fabrication, the use of sodium carboxy-methyl cellulose (CMC) as binder material is common, due to its role as a thickening agent of the slurry and solubility in water. However, due to its brittleness, the usage of CMC requires additional binders to maintain flexibility of the coating. The ratio of active and inactive materials within the cell is strongly correlated to its capacity and the addition of these binders ultimately results in a decreased energy density of the cell. Besides keeping the particles together, the main purpose of the binder is to guarantee good adhesion to the substrate. Therefore, a high concentration is not necessarily needed at the top of the coating and the overall amount of binder material should be kept at a minimum. Bi-layered cathodes consisting of Ni-rich lithium nickel manganese cobalt oxides (NMC811) as active material were fabricated. The concentration of poly(methyl)acrylate (PMA) binder was changed in the top layer and its effect on structural properties and electrochemical performance was investigated. Water-based processed cathodes with high loadings of more than 8 mAhcm -2 were tested in full cell configurations. Reduction of the binder content leads to an increase in specific discharge capacity of up to 40% compared to single-layered and 25% to unmodified multi-layered electrodes at a C-rate of 1C (Figure 1b). Acknowledgements This work was financially supported by the Austrian Federal Ministry for Climate Action, Environment, Energy, Mobility, Innovation and Technology (bmk). [1] Z. Du, D.L.W. Iii, C.D.S. Kalnaus, J. Li, Understanding limiting factors in thick electrode performance as applied to high energy density Li-ion batteries, J. Appl. Electrochem. 47 (2017) 405–415. https://doi.org/10.1007/s10800-017-1047-4. [2] Y. Kuang, C. Chen, D. Kirsch, L. Hu, Thick Electrode Batteries: Principles, Opportunities, and Challenges, Adv. Energy Mater. 9 (2019). https://doi.org/10.1002/aenm.201901457. [3] F. Font, B. Protas, G. Richardson, J.M. Foster, Binder migration during drying of lithium-ion battery electrodes: Modelling and comparison to experiment, J. Power Sources. 393 (2018) 177–185. https://doi.org/10.1016/j.jpowsour.2018.04.097. [4] M. Müller, L. Pfaffmann, S. Jaiser, M. Baunach, V. Trouillet, F. Scheiba, P. Scharfer, W. Schabel, W. Bauer, Investigation of binder distribution in graphite anodes for lithium-ion batteries, J. Power Sources. 340 (2017) 1–5. https://doi.org/10.1016/j.jpowsour.2016.11.051. [5] L. Neidhart, K. Fröhlich, N. Eshraghi, D. Cupid, F. Winter, M. Jahn, Aqueous Manufacturing of Defect-Free Thick Multi-Layer NMC811 Electrodes, Nanomaterials. 12 (2022) 1–15. https://doi.org/10.3390/nano12030317. Figure 1

Optimized battery electrodes with primer layers by simultaneous two-layer slot-die coating

Simultaneous Primer Coating for Fast Drying of Battery Electrodes

Improvement of Lithium‐Ion Battery Performance by Two‐Layered Slot–Die Coating Operation

Slot-die processing of lithium-ion battery electrodes—Coating window characterization

Slot die coating of lithium-ion battery electrodes: investigations on edge effect issues for stripe and pattern coatings

The Role of Polymer and Inorganic Coatings to Enhance Interparticle Connections Diagnosed by in Situ Techniques.

Experimental investigation of the multi-layer wetting behavior of electrode-separator-composites in lithium-ion batteries

Innovative Battery Electrodes Via Composite Electroforming

Advancements in Dry Coating for Battery Electrodes: Scalable Extrusion Mixing for Control of Electrode Microstructure and Electrochemical Performance

Process- Structure Property Correlations in Continuous Processing of High-Power Anode Electrode Pastes for Application in Lithium Ion Batteries

Benefits of Tuned Binder Distribution in Multi-Layered Thick NMC811 Cathodes

Layered/Layered Homostyructure Ion Conductor Coating Strategy for High Performance Lithium Ion Batteries

Dual-Protective Artificial Layer on Lithium Metal Anodes for Improved Electrochemical Performance – an in-Depth Morphological and Electrochemical Characterization

Enabling High-Performance Battery Electrodes by Surface-Structuring of Current Collectors and Crack Formation in Electrodes: A Proof-of-Concept

Enabling the Production of Homogeneous High-Load Positive Electrodes by Tailoring the Electrode Formulation – a Conductive Additive and Solvent Approach

Advances in the Aqueous Processing of Ni-Rich Positive Electrodes

Tunable Conformal Electrodeposition of Ultra-Thin Polymeric Films for Electrolyte Interphases

Slot-die-coating operability windows for polymer electrolyte membrane fuel cell cathode catalyst layers

Phase-Separation-Induced Porous Lithiophilic Polymer Coating for High-Efficiency Lithium Metal Batteries

Multi‐Element Surface Coating of Layered Ni‐Rich Oxide Cathode Materials and Their Long‐Term Cycling Performance in Lithium‐Ion Batteries

Synergistic Effects of Surface Coating and Bulk Doping in Ni‐Rich Lithium Nickel Cobalt Manganese Oxide Cathode Materials for High‐Energy Lithium Ion Batteries