Abstract:Direct AC–AC converters are strong candidates in the power converting system to regulate grid voltage against the perturbation in the line voltage and to acquire frequency regulation at discrete step levels in variable speed drivers for industrial systems. All such applications require the inverted and non-inverted form of the input voltage across the output with voltage-regulating capabilities. The required value of the output frequency is gained with the proper arrangement of the number of positive and negative pulses of the input voltage across the output terminals. The period of each such pulse for low-frequency operation is almost the same as the half period of the input grid or utility voltage. These output pulses are generated by converting the positive and negative input half cycles in noninverting and inverting forms as per requirement. There is no control complication to generate control signals used to adjust the load frequency as the operating period of the switching devices is normally greater than the period of the source voltage. However, high-frequency pulse width modulated (PWM) control signals are used to regulate the output voltage. The size of the inductor and capacitor is inversely related to the value of the switching frequency. Similarly, the ripple contents of voltage and currents in these filtering components are also inversely linked with PWM frequency. These constraints motivate the circuit designer to select high PWM frequency. However, the alignment of the high-frequency control input with the variation in the input source voltage is a big challenge for a design engineer as the switching period of a high-frequency signal normally lies in the microsecond. It is also required to operate some high-frequency devices for various half cycles of the source voltage, creating control complications as the polarities of the half cycles are continuously changing. This requires at least the generation of two high-frequency signals for different intervals. The interruption of the filtering inductor current is a big source of high voltage surges in circuits where the high-frequency transistors operate in a complementary way. This may be due to internal defects in the switching transistors or some unnecessary inherent delay in their control signals. In this research work, a simplified AC–AC converter is developed that does not need alignment of high-frequency control with the polarity of the source voltage. With this approach, high-frequency signals can be generated with the help of any analog or digital control system. By applying this technique, only one high-frequency control signal is generated and applied in AC circuits, as in a DC converter, without applying a highly sensitive polarity sensing circuit. So, controlling complications is drastically simplified. The circuit and configuration always avoid the current interruption problem of filtering the inductor. The proposed control and circuit topology are tested both in computer-based simulation and practically developed circuits. The results obtained from these platforms endorse the effectiveness and validation of the proposed work.

A single‐phase AC‐AC converter with continuous input current and without commutation problem

An isolated high‐gain impedance source‐based single‐phase AC–AC converter with safe commutation and variable output frequency

Soft-Switching Single-Stage Current-Fed Full-Bridge Isolated Converter for High Power Ac/Dc Applications

Novel High-Efficiency Frequency-Variable Buck–Boost AC–AC Converter With Safe-Commutation and Continuous Current

A high-efficiency single-phase AC/DC converter with enabling window control and active input bridge

High-Efficiency Single-Phase AC–AC Converters Without Commutation Problem

A Novel Family of Single‐Phase Direct Buck AC‐AC Converters With Continuous Input Current, Reduced Components, and Balanced Power Losses

Control and Modulation of a Single-Phase AC/DC Converter with Smooth Bidirectional Mode Switching and Symmetrical Decoupling Voltage Compensation

Highly Efficient Single Power-Conversion Resonant DC/AC Converter Without Output Filter

A New Single-Phase Isolated Improved Quasi Z-Source AC–AC Converter

New single-switch buck-boost converter with continuous input/output currents and a wide conversion range

Switched-LC Based High Gain Converter with Lower Component Count

Three-Level Isolated Direct AC–AC Converter and Its Closed-Loop Control Strategy

Highly Efficient Three-Level AC–AC Converter With Identical In-Phase and Antiphase Buck–Boost Operations

A family of single‐phase boost AC‐AC converters based on impedance network cells with symmetric bipolar operation

Single-phase Direct AC-DC Bidirectional Converter Featuring Natural Power Factor Correction

Design and implementation of an innovative single-phase direct AC-AC bipolar voltage buck converter with enhanced control topology

Three Switch Three Phase Inverter With Improved DC Voltage Utilization

A Current-Fed Multiresonant Converter with Low Circulating Energy and Zero-Current Switching for High Step-Up Power Conversion

Phase-shifted controlled forward mode AC/AC converters with high frequency AC links

A New Continuous Input Current Nonisolated Bidirectional Interleaved Buck-Boost DC-DC Converter