Abstract:The aim of the study was to evaluate the influence of key waveform factors on the dynamics of the process during injection molding of cast iron with granular magnesium in ladles, their significance and relationship between them. Based on the theories of wave motion of liquid layers, a mathematical model has been developed that allows to investigate the oscillatory processes in the ladle during the processing of cast iron melt with granular magnesium. The model involved the processing of cast iron by injection of granular magnesium through the tuyeres of devices that are immersed in the melt. The oscillating system "Liquid bath - lance" is considered on the example of the bath of a heavy - duty filling bucket with its own frequency - 0.47 Hz. The influence of the most probable oscillation sources (natural frequency of the lance oscillation and the frequency of the conditional source) on the amplitude-frequency oscillations of the system elements is calculated. It is established that in addition to the natural frequencies of these elements, the system has two more natural oscillations. Given that the mass of the melt is much greater than the mass of the lance, it practically determines the behavior of the system during its excitation. That is, the system responds only to those excitations in which the frequency is close to the natural frequency of the liquid bath. In turn, it is shown that the natural frequency of the bath is largely determined by its diameter at the top. In practice, it is necessary to know the resonant frequencies of the liquid bath, the tuyere device, as well as all other sources of oscillations (gas jet decay, and oscillations of pop-up bubbles). Accordingly, it is necessary to try to dampen the amplitude with this dangerous resonant frequency. To reduce the oscillation amplitude of the bath surface when treating cast iron with granular magnesium, it is recommended to first estimate the natural resonant frequency of the liquid bath, and then select design solutions and processing parameters, avoiding dangerous frequencies close to the natural frequency of the bath. However, it should be noted that the spectrum of oscillation frequencies in the purl zone is quite wide and, of course, contains dangerous low frequencies.

Analysis of Surface Behavior and Cavity Oscillations in a Liquid Metal Model Experiment of the Basic Oxygen Furnace Process

Numerical Simulation of the Interaction Between Supersonic Oxygen Jets and Molten Slag–Metal Bath in Steelmaking BOF Process

Analysis of the shear-driven flow in a scale model of a phase separator: Validation of a coupled CFD approach using experimental data from a physical model

Flamelet LES of a 40 Kwth Pulverized Torrefied Biomass Furnace in Air and Oxy-Fuel Atmospheres

THE CHARACTERISTIC CAVITY SIZE IN BASIC OXYGEN STEELMAKING CONVERTER

Mathematical Modeling of the Ejected Droplet Size Distribution in the Vicinity of a Gas–Liquid Impingement Zone

Modeling Freeze‐Lining Formation: A Case Study in the Slag Fuming Process

Rearrangement of Liquid Metal Surface Waves by a Uniform Transverse Magnetic Field

Enhanced impingement characteristics of supersonic oxygen jets on molten bath using a multi-nozzle oxygen lance in a converter

Identifying Surface Structural Changes in a Newly-Developed Ga-based Alloy with Melting Temperature below 10 °C

Oxygen Distribution at the Hot Spot in BOF Steelmaking

Modeling the Residence Time of Metal Droplets in Slag During BOF Steelmaking

Dynamics of oscillations of the "liquid bath - lance" system during injection processing of the melt in the ledle

Interfacial phenomena between molten iron and molten slag–Effect of nitrogen on the Marangoni convection

Marangoni driven turbulence in high energy surface melting processes

Influence of oxygen content on melt pool dynamics in metal additive manufacturing: High-fidelity modeling with experimental validation

Effect of Furnace Gas Composition on Characteristics of Supersonic Oxygen Jets in the Converter Steelmaking Process

SURFACE TENSION DRIVEN MOLTEN METAL FLOW OVER FLAT AND/OR GROOVED REACTIVE SURFACES DURING BRAZING AND SOLDERING

Modeling of oxidation of structural materials in LBE systems

Analysis on phase distribution and flow field morphology in double side blown gas-liquid mixture flows with high temperature and high density melt

Water model experiment on the liquid flow behavior in a bottom blown bath with top layer