Abstract:The flow condensation heat transfer coefficient of R134a inside two helical micro-fin tubes with outer diameter of 6.35 mm and helical angles of 18o and 28o respectively were experimentally studied at a high mass flux ranging from 500 to 1100 kg m−2 s−1. The condensation temperatures are 35°C, 40°C and 45°C, and the vapor qualities ranges from 0.95 to 1.00 at the inlet section and from 0.00 to 0.05 at the outlet section. Experimental results show that there are annular and intermittent flow regimes inside the tube under experimental conditions, the ratio of annular flow region to the total heat transfer region is about 70%. The liquid film flow changes from rotational flow to coexistence of rotational and horizontal flows when the vapor quality is 0.475±0.08, 0.486±0.06 and 0.521±0.05, respectively and the corresponding saturation temperature is 35°C, 40°C and 45°C. Based on the experimental data, the heat transfer coefficient increases with increasing mass flux and fin helical angle, and with decreasing saturation temperature and Reynolds number of cooling water. In addition, the heat transfer coefficient of annular flow is greater than that of intermittent flow, in other words, the heat transfer coefficient increases with increasing vapor quality. The heat transfer coefficient obtained at high mass flux was compared with the calculated data of some published correlations used at low mass flux. It was found that most correlations underestimate the experimental heat transfer coefficient inside the micro-fin tube, and these prediction deviation increases with increasing mass flux and fin helical angle. By introducing some dimensionless numbers as well as considering the flow mechanism of liquid film inside the tube, two heat transfer coefficient correlations were proposed based on the experimental data. The ratio of liquid film thickness to fin height was used to characterize whether the liquid film flow is rotational flow or coexistence of rotational and horizontal flows in the proposed correlation, which shows a better prediction accuracy with a mean deviation of less than 7.3%.

Ammonia flow boiling in the smooth, annuli and inner-finned tube at different gravity orientation

Flow boiling heat transfer and dryout characteristics of ammonia in a horizontal smooth mini-tube

Flow Boiling in Horizontal Annuli Outside Horizontal Smooth, Herringbone and Three-Dimensional Enhanced Tubes

Experimental study of ammonia flow boiling in a vertical tube bundle: Part 2-Enhanced dimple tube with full length solid round PVC nonconductive rod

Experimental Study of Ammonia Flow Boiling in a Vertical Tube Bundle: Part 4 – Comparative Analysis

Experimental Study of Ammonia Flow Boiling in a Vertical Tube Bundle: Part 1 – Enhanced Dimple Tube

Flow Boiling in Inner Annulus of Horizontal Enhanced Tubes

Experimental Study of Condensation Heat Transfer of R134a Inside the Micro-Fin Tubes at High Mass Flux

Pool boiling heat transfer of ammonia outside enhanced tubes with various fin structures

Experimental Study of Flow Boiling Instabilities in Horizontal Tubes under Gas–liquid Stratification Condition: Effects of Heat Flux and Inlet Subcooling Degree

R410A flow boiling coefficient in horizontal annular channels of enhanced tubes, Part II: Heat transfer

Experimental Investigation on Two-Phase Flow Pattern of Ammonia Inside 4 Mm and 8 Mm Horizontal Smooth Tubes

Boiling Heat Transfer and Visualization for R717 in a Horizontal Smooth Mini-tube

Ammonia single-phase and two-phase frictional pressure losses in horizontal smooth and straight inner-grooved tubes

Heat Transfer Characteristics Of Ammonia During Flow Boiling In A Horizontal Small Diameter Tube

Numerical investigations on flow boiling heat transfer of ammonia water binary solution (NH3/H2O) in a horizontal microchannel

R410A flow boiling in horizontal annular channels of enhanced tubes, part I: Pressure drop

Experimental Analysis of Flow Boiling in Horizontal Annulus—The Effect of Heat Flux on Bubble Size Distributions

Evaporative annular flow in micro/minichannels: A simple heat transfer model

Numerical investigation of flow boiling characteristics of R134A in a smooth horizontal tube

Flow Boiling Characteristics Of R410a In Horizontal Annuli Of Enhanced Surface Tubes