Abstract:Recently, sodium ion batteries (NIBs) gained increasing attention, because of its abundant reserves and relatively even geological distribution. However, the development of NIBs is greatly hampered because of the lack of appropriate active materials for both cathodes and anodes. Since the Na ion is ca. 55% larger than the Li ion, finding suitable host materials with sufficiently large interstitial space to accommodate sodium ions and to allow reversible and rapid ion insertion and extraction is very difficult. NASICON-type Na3V2(PO4)3 has recently been considered as a prospective cathode material for NIBs, because of its highly covalent 3D framework crystalline structure, high energy density (~400 Wh/kg) and good thermal stability. For anode materials, disordered carbon is particularly attractive because of their large interlayer distance and disordered structure that could accommodate sodium ions. Here, we briefly present porous carbon based electrodes for NIBs with excellent rate performance: (1) Carbon-coated nanosized Na3V2(PO4)3 embedded in the porous carbon matrix (abbreviated as CC-NVP@PCM); (2) Nitrogen-doped activated porous carbon fibers (ACFs); (3)Flexible free-standing porous carbon nanofibers (P-CNFs) with three-dimensional (3D) interconnected structure. The CC-NVP@PCM was prepared by using a facile soft-chemistry based method with post heat-treatment. It shows high rate performance (44 mAhg-1at 200C ). This ultrahigh rate performance is comparable to that of supercapacitor, but with much higher energy density. The ACFs were synthesized by pyrolysis of Ppy nanofiber precursor. It shows excellent capacity retention and extraordinary rate performance. The reversible capacity at 0.05 Ag-1 is 296 mAhg-1 and could still maintain as 72 mAg-1 at a current of 10 Ag-1. In case of the P-CNFs electrode prepared by electrospinning, it delivers a reversible capacity of 266 mAh.g-1 after 100 cycles at 0.2C, corresponding to 80.3 % of the initial charge capacity. When cycled at a current density as high as 500 mAg-1 (2C), it still delivers a reversible capacity of ~140 mAh.g-1after 1000 cycles. The improvement of electrochemical performance of these porous carbon based electrodes for NIBs is attributed to the special design and porous structure, which confined a variety of advantages: hierarchical porous channels enabling short transport length for ions and electrons, carbon coated structure resulting in low resistances, good mechanical properties leading to the excellent morphology stability.

Low-Cost, High-Energy Na-Ion Hybrid Supercapacitors

Nanostructured LiMn2O4 Composite As High-Rate Cathode for High Performance Aqueous Li-ion Hybrid Supercapacitors

Rapid Synthesis of Mn-Doped NiFe2O4 Nanosheet Arrays for High-Performance Hybrid Supercapacitors

Adapting a Kinetics-Enhanced Carbon Nanostructure to Li/Na Hybrid Water-in-Salt Electrolyte for High-Energy Aqueous Supercapacitors

Synthesis of NiMn-LDH Nanosheet@Ni 3 S 2 Nanorod Hybrid Structures for Supercapacitor Electrode Materials with Ultrahigh Specific Capacitance

N, S Co-doped hierarchical porous carbon rods derived from protic salt: Facile synthesis for high energy density supercapacitors

Low cost Na2FeSiO4/H–N-doped hard carbon nanosphere hybrid cathodes for high energy and power sodium-ion supercapacitors

A High Capacity, Good Safety and Low Cost Na2FeSiO4-Based Cathode for Rechargeable Sodium-Ion Battery.

Electrospun Na3V2(PO4)3/carbon composite nanofibers as binder-free cathodes for advanced sodium-ion hybrid capacitors

Carbon-incorporated NaTi2(PO4)3 on carbon cloth as a binder-free anode material for high-performance aqueous sodium-ion hybrid capacitors

Highly Stable Na3Fe2(PO4)3@Hard Carbon Sodium-Ion Full Cell for Low-Cost Energy Storage

Electrodes for Sodium-Ion Batteries with Excellent Rate Performance Using Porous Carbon Networks

A New Polyanion Na 3 Fe 2 (PO 4 )P 2 O 7 Cathode with High Electrochemical Performance for Sodium-Ion Batteries

Nitrogen-doped porous carbon nanofoams with enhanced electrochemical kinetics for superior sodium-ion capacitor

A Scalable Approach to Na 2 FeP 2 O 7 @Carbon/Expanded Graphite as a Low‐Cost and High‐Performance Cathode for Sodium‐Ion Batteries

A High-Energy-Density Hybrid Supercapacitor with P-Ni(OH)2 @Co(OH)2 Core-Shell Heterostructure and Fe2 O3 Nanoneedle Arrays as Advanced Integrated Electrodes

High-performance sodium-ion capacitors with SnS2/ZnS-reduced graphene oxide anodes and biomass waste-derived porous carbon cathodes

Carbon Coated MoS2 Nanosheets Vertically Grown on Carbon Cloth As Efficient Anode for High-Performance Sodium Ion Hybrid Capacitors

ZnFe2O4@Carbon Core-Shell Nanoparticles Encapsulated in Reduced Graphene Oxide for High-Performance Li-Ion Hybrid Supercapacitors

Na4Fe3(PO4)2(P2O7)@C/Ti3C2Tx Hybrid Cathode Materials with Enhanced Performances for Sodium-Ion Batteries

High Performance Flexible Quasi-Solid-state Zinc-Ion Hybrid Supercapacitors Enable by Electrode Potential Adjustment