Abstract:The dynamic ‘overstress’, i.e., the apparent increase of strength of concrete at very high strain rates (10–106\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$$10^{6}$$\end{document}/s) experienced in projectile impact and penetration, has recently been explained by a new theory with partial analogy to turbulence. The increase is attributed to comminution of concrete driven by the release of local kinetic energy of the shear strain rate field of forming fragments which, in projectile impact problems, exceeds the strain energy of the fragments by orders of magnitude. This theory gives the particle size distribution and the additional local kinetic energy density, ΔK\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$$\Delta K$$\end{document}, proportional to the deviatoric strain rate square. To match test results, ΔK\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$$\Delta K$$\end{document} must be dissipated during finite element simulations of impact. In previous simulations, ΔK\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$$\Delta K$$\end{document} was, at first, dissipated by an artificial equivalent viscosity (not empirical but predicted by the theory). Later it was found that dissipation by upscaling material tensile strength is equally effective. This theoretically justified upscaling is adopted here since it is more realistic when microplane constitutive model M7 for fracturing damage in concrete is used. All artificial damping is eliminated from the computer program. While previous simulations with the comminution theory were limited to orthogonal impacts, and only the cases of penetration of slabs of various thickness by projectile of one velocity and penetration depths for different velocities, the present study also analyzes further test data on oblique impacts at various impact angles up to 35∘\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$$35^\circ $$\end{document}, and on the exit velocities and penetration depths of projectiles of different velocities. For each test series on one and the same concrete, the material parameters are calibrated on one test and then, using the same parameters, all the other tests are predicted. All the predictions of exit velocities and penetration depths of projectiles, as well as entry and exit craters, are quite accurate.

Fastening in concrete vs. rock mass—Comparative determination of pull‐out loads for artificially created discontinuities in concrete

Fastening in Rock Mass—Structural Design of Shallow Embedded Anchors in Inhomogeneous Substrate

Numerical Investigation of the Formation of a Failure Cone during the Pullout of an Undercutting Anchor

Comparison of pull-out capacities of robotically and manually drilled and set fasteners

Mechanism and Internal Stability of Supportive Stone Constructions

Experimental pull-out tests and design indications for strength anchors installed in masonry walls

Concrete screws in contact with reinforcement

Load Capacity of Screw Anchor Installed in Concrete Substrate Reinforced with Steel Fibers Depending on Fiber Content

Experimental Study on Direct Shear Performance of Concrete-Concrete Interface of Prefabricated Structure Sleeve Grouting Connection

Pullout Response of Ultra-High-Performance Concrete with Twisted Steel Fibers

A Field Investigation of Pullout Resistance of Steel Anchors in Rock

Experimental Study of the Shear Strength of Bonded Concrete–Rock Interfaces: Surface Morphology and Scale Effect

Laboratorial Tests and Numerical Modeling of Rock Bolts Bonded by Different Materials

Design Recommendations for Concrete Pryout Capacity of Headed Steel Studs and Post-Installed Anchors

Field and Laboratory Investigation of Pullout Resistance of Steel Anchors in Rock

Experimental Research on Dynamic Failure of Rock–Cemented Material–Rock Interface Considering Strain Rate Effect

Befestigungen im stahlfaserverstärkten Beton bei Betonbruch – Stand der Technik und Bemessungsansatz/Anchorages in Steel Fiber Reinforced Concrete in the case of concrete breakout failure – State of the art and design concept

Consistent time-to-failure tests and analyses of adhesive anchor systems

Assessment of concrete–rock contact shear behaviour based on in situ shear tests

An experimental and numerical investigation of concrete pry-out failure after fire exposure: Group effects and failure mechanism

Effect of high-rate dynamic comminution on penetration of projectiles of various velocities and impact angles into concrete