Abstract:The transformation of N/S/Cl during pyrolysis of waste tire were investigated by Thermogravimetry-Mass Spectrum (TG-MS) and flow tube furnace reactor. The pyrolysis of waste tire included four stages, i.e., dehydration below 200 ℃, decomposition of tire additives at 200∼300 ℃, degradation of natural rubber at 300∼420 ℃, and cracking of synthetic rubber at 420∼500 ℃. The activation energy Eα were calculated according to the Coats-Redfern integral method, ca. 154.72∼158.23 and 200.46∼231.58 kJ/mol for degradation of natural rubber and synthetic rubber, respectively. Most of nitrogen (60.32∼67.78 wt.%), sulfur (56.73∼62.38 wt.%), and chlorine (58.60∼64.92 wt.%) were remained in the pyrolytic char. For the pyrolytic oil composition, expect for alkanes, alkenes, aromatic hydrocarbons, and oxygenates, the S-containing disulfide and sulfurous acid ester, N-containing quinoline and pyrimidine diamine, and Cl-containing silane, dichlorododecylmethyl- were detected. The nitrogen, sulfur, and chlorine in pyrolytic gas had diverse types. The N-containing pollutants mainly derived from inorganic ammonium and heterocyclic-N. NH3 had a wide releasing temperature range, while NO, HCN, and HNCO were mainly generated at 300∼600 °C. The C-S and -SH radicals mainly contributed to S-containing pollutants, i.e., H2S, COS, CS2, SO2, CH3SH, and C6H5SH. The Cl-containing pollutants exhibited dominant release within the temperature range of 300∼600 °C. Overall, higher heating rate promoted gas emissions, especially for NO, HCN, CH3SH, and HCl. This article provides basic knowledge on hazardous N/S/Cl transformation in solid char, liquid oil, and gas during pyrolysis of waste tire that will provide valuable information for future control technologies of pollutants emission.

Investigation of the sulfur enrichment mechanism on the catalyst in the FCC process of waste tire pyrolytic oil

Desulfurization and upgrade of pyrolytic oil and gas during waste tires pyrolysis: The role of metal oxides

Effect of spent fluid catalytic cracking (FCC) catalyst on syngas production from pyrolysis and CO2-assisted gasification of waste tires

Co-pyrolysis of Corn Stover and Waste Tire: Pyrolysis Behavior and Kinetic Study Based on Fraser-Suzuki Deconvolution Procedure

Molecular dynamics study of waste tire pyrolysis: Focus on intermediate product evolution and sulfur migration law

Study on pyrolysis characteristics, kinetics and thermodynamics of waste tires catalytic pyrolysis with low-cost catalysts

Spent fluid catalytic cracking (FCC) catalyst enhances pyrolysis of refinery waste activated sludge

Production of low-sulfur fuels from catalytic pyrolysis of waste tires using formulated red mud catalyst

Enhanced Hydrothermal Liquefaction of Tires Using Zinc and MoS2

Catalytic Mechanism of MCM-41 Supported Phosphoric Acid Catalyst for FCC Gasoline Desulfurization by Alkylation: Experimental and Theoretical Investigation

Waste tire heat treatment to prepare sulfur self-doped char via pyrolysis and K2FeO4-assisted activation methods

A Novelty Catalytic Reforming of Tire Pyrolysis Oil for Hydrogen-Rich Syngas

Pyrolytic transformation behavior of hydrocarbons and heteroatom compounds of scrap tire volatiles

Enhancing light fuel production through catalytic pyrolysis of municipal mixed plastic waste over activated spent FCC catalyst

Characteristics, kinetics, infrared analysis and process optimization of co-pyrolysis of waste tires and oily sludge

Study on pyrolysis of waste tires and condensation characteristics of products in a pilot scale screw-propelled reactor

Sustainable valorization of waste tires: Selective hydrotreating for renewable p-cymene production

Waste tire derived char supported Ni‐Fe catalyst for catalytic thermochemical conversion of wet municipal solid waste

Kinetic analysis of waste tire pyrolysis with metal oxide and zeolitic catalysts

The promoting and inhibitory mechanism of interaction between waste tires and Spirulina on their co-pyrolysis

Transformation of nitrogen, sulfur and chlorine during waste tire pyrolysis