Abstract:Lithium ion batteries (LIBs) are very important power sources in a variety of applications, including portable electronic devices and home electronics, and are expanding to electric vehicles nowadays. The rapid development of these applications demands for making LIB smaller and lighter, namely, requires incorporation of higher gravimetric and volumetric capacity materials to replace the currently commercialized graphite anode[1]. Silicon (Si) is the most attractive anode material due to its high theoretical capacity of 3579 mAh g-1 at room temperature, which is an order higher in magnitude than that of graphite (372 mAh g-1)[2]. However, the poor cycleability, which is caused by structural failure and pulverization due to the huge volume change (>300%) of Si during the Li+insertion and removal, hinders its practical application. In order to enhance the cycling performance, one of the promising ways is reducing the particle size of Si into nano-crystallite or amorphous structure to minimize the expansion, and then dispersing the as-obtained Si in the carbon matrix which mostly functioned as an elastic network with high e-/Li+ conductivity[3]. In contrst to the rather complicated deposition synthesis, ball milling (BM) is considered to be an effective approach to obtain nanosized powder materials, which is also favorable for large scale production. In this work, we report an amorphous-Si/WC@graphene (SW@G) composite anode with improved performance had been designed and produced by a simple two-step BM process. [4] It should be noted that the rigid wolframcarbide (WC) particles were expected to assist refining of the common micro-sized Si to the amorphous state gradually in milling process. Resemble a concrete structure, the SW@G composite consisted of multiple-scale WC particles which were uniform distributed in amorphous Si (a-Si) matrices, with outside coating by few layers of graphene (Fig.1). The greatly enhaced structural stability of SW@G composite can be attributing to the following reasons: (i) the lithiation and the subsequent volume expansion of a-Si would have no preferred orientations in the SW@G; (ii) the multiple-scale WC particles not only act as the gravel to strengthen the inside structure to withstand the pulverizations and aggregations of Si during cycling, but also provides proper electric contact between the Si particles due to their high intrinsic electronic conductivity; (iii) like the outside cement layers of concrete, the GNs layers work as shell of the whole SW@G composite, cloud much improve the electronic conductivity among the SW@G particles, as well as help to form a stable SEI film to keep the inside Si from directly exposing to electrolyte. In these viewpoints, this concrete-like structure could lead to a high structure stability and consequently a good cycleability, as well as a superior rate performance for the SW@G composite. Acknowledgements : This work was supported by the National Science Foundation of China (Projects 51201065 and 51231003), by the Guangdong National Science Foundation (Project S2013010012487), and by the Doctorate Foundation of the Ministry of Education (Projects 20120172120007). References 1. B. Wang, M. Liang, L. Zhi, Nano letters, 2013, 13, 5578. 2. W. J. Zhang, J. Power Sources 2011, 196, 13. 3. W. Sun, R. Z. Hu, M. Zhu, J. Power Sources 2008, 53, 3377. 4. W. Sun, R. Z. Hu, M. Zhu, Electrochim. Acta 2016, 191, 462 Figure 1

Architecting Sturdy Si/Graphite Composite with Lubricative Graphene Nanoplatelets for High‐Density Electrodes

Calendering-Compatible Macroporous Architecture for Silicon-Graphite Composite toward High-Energy Lithium-Ion Batteries

Fabrication of Graphene Nanoplatelets-Supported Siox-Disordered Carbon Composite and Its Application in Lithium-Ion Batteries

Scalable Layer-by-Layer Stacking of the Silicon-Graphite Composite: Prelithiation Strategy of the High-Capacity Anode for Energy/Power-Dense Li Batteries

Roll to roll manufacturing of fast charging, mechanically robust 0D/2D nanolayered Si-graphene anode with well-interfaced and defect engineered structures

Engineering Polymer-Assisted Self-Assembly Process for High-Capacity and Cycle-Stable Si-on-Graphite Anode of Li-Ion Batteries

Covalent Coating of Micro‐Sized Silicon With Dynamically Bonded Graphene Layers Toward Stably Cycled Lithium Storage

Compact Si/C Anodes Fabricated by Simultaneously Regulating the Size and Oxidation Degree of Si for Li-Ion Batteries

Scalable Synthesis of Pitch-Coated Nanoporous Si/Graphite Composite Anodes for Lithium-Ion Batteries

3D binder-free nanoarchitecture design of porous silicon/graphene fibers for ultrastable lithium storage

Integrating highly active graphite nanosheets into microspheres for enhanced lithium storage properties of silicon

g-C3N4 integrated silicon nanoparticle composite for high-performance Li-ion battery anodes

Silicon/Wolfram Carbide@Graphene Composite: Enhancing Conductivity and Structure Stability in Amorphous-Silicon for High Lithium Storage Performance

Scalable synthesis of N-doped Si/G@voids@C with porous structures for high-performance anode of lithium-ion batteries

Suppressing Deformation of Silicon Anodes via Interfacial Synthesis for Fast‐Charging Lithium‐Ion Batteries

Facile preparation of silicon/carbon composite with porous architecture for advanced lithium-ion battery anode

Interfacially Induced Cascading Failure in Graphite‐Silicon Composite Anodes

Constructing LiF‐Enriched Solid Electrolyte Interface on Graphene Arrays with Abundant Edges on Microscale Si‐C Anodes Toward High‐Energy Lithium‐Ion Batteries

Encasing Prelithiated Silicon Species in the Graphite Scaffold: An Enabling Anode Design for the Highly Reversible, Energy-Dense Cell Model

“Sticky” carbon coating enables high-area-capacity lithium storage of silicon-graphitic carbon hybrid

Boosting the lithium and sodium storage performance of graphene-based composite via pore engineering and surface protection