A New Strategy of 3D Printing Lightweight Lamellar Graphene Aerogels for Electromagnetic Interference Shielding and Piezoresistive Sensor Applications

Hao Guo,Tianxiang Hua,Jing Qin,Qixin Wu,Rui Wang,Bo Qian,Lingying Li,Xuejun Shi

DOI: https://doi.org/10.1002/admt.202101699

IF: 6.8

2022-03-11

Advanced Materials Technologies

Abstract:Advanced Materials Technologies, EarlyView.

materials science, multidisciplinary

What problem does this paper attempt to address?

Lightweight Microwire/graphene/silicone Rubber Composites for Efficient Electromagnetic Interference Shielding and Low Microwave Reflectivity

Y. L. Xu,A. Uddin,D. Estevez,Y. Luo,H. X. Peng,F. X. Qin

DOI: https://doi.org/10.1016/j.compscitech.2020.108022

IF: 9.1

2020-01-01

Composites Science and Technology

Abstract:Most traditional fillers used in electromagnetic shielding composites require high loading, uniform distribution and complicated structures for modest property enhancement. Here, we propose a simple shielding system incorporating magnetic microwires M and graphene fibers G in different arrangements. Integrating both fillers in the composite resulted in superior shielding effectiveness (SE) with respect to incorporating either individual type of filler, due to improved absorption efficiency, impedance matching and polarization triggered by different arrangements of the fillers. Randomly dispersed arrays provided a maximum shielding of 6 dB for equal amount of G and M, in which polarization effects at the interface between the two regions contributed to the SE value. The highest SE of 18 dB (98.4% attenuation) was reached by the MMMGGG periodic arrays with merely 0.059 wt % filler loading enabled by the optimized arrangement and wave attenuation from the microwires dielectric/magnetic response. The normalized SE of this composite was about two to four orders of magnitude higher than that of many other shielding candidate materials. High SE, low loading, simple structure, and multifunctionality make these composites attractive for several applications. Moreover, tailoring topological and structural factors of both fillers would facilitate further SE enhancement without sacrificing the important lightweight advantage.
Ultralight, Conductive Ti3C2Tx MXene/PEDOT:PSS Hybrid Aerogels for Electromagnetic Interference Shielding Dominated by the Absorption Mechanism

Guo-Yu Yang,Shao-Zhe Wang,Hong-Tai Sun,Xu-Ming Yao,Chuan-Bing Li,Yu-Jun Li,Jian-Jun Jiang

DOI: https://doi.org/10.1021/acsami.1c13303

IF: 9.5

2021-01-01

ACS Applied Materials & Interfaces

Abstract:MXene aerogels with a porous microstructure are a promising electromagnetic interference (EMI) shielding material due to its low density and excellent electrical conductivity, which has attracted widespread attention. Compared with traditional EMI shielding materials that rely on reflection as the primary mechanism, MXene aerogels with absorption as the dominant mechanism have greater potential for development as a novel EMI shielding material because of its ability to reduce environmental contamination from reflected electromagnetic (EM) waves from materials. In this study, a novel Ti3C2Tx MXene/PEDOT:PSS hybrid aerogel was presented by freeze-drying and thermal annealing using few-layered Ti3C2Tx MXene and the conductive polymer poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT:PSS). PEDOT:PSS not only improved the gelling ability of Ti3C2Tx but also successfully established a conductive bridge between MXene nanosheets. The experimental results demonstrated that the hybrid aerogel exhibited an obvious porous microstructure, which was beneficial for the multiple scattering of EM waves within the materials. The EMI shielding effectiveness and specific shielding effectiveness reached up to 59 dB and 10,841 dB·cm2·g-1, respectively, while the SER/SET ratio value was only 0.05, indicating superior wave absorption performance. Furthermore, the good impedance matching, due to the electrical conductance loss and polarization loss effect of the composites, plays a critical role in their excellent wave absorption and EMI shielding performance. Therefore, this work provides a practical approach for designing and fabricating lightweight absorption-dominated EMI shielding materials.
3D printing of resilient, lightweight and conductive MXene/ reduced graphene oxide architectures for broadband Electromagnetic Interference shielding

Yang Dai,Xinyu Wu,Lulu Li,Yu Zhang,Zhiming Deng,Zhong-Zhen Yu,Hao-Bin Zhang

DOI: https://doi.org/10.1039/d2ta01388f

IF: 11.9

2022-01-01

Journal of Materials Chemistry A

Abstract:Lightweight and conductive macroscopic MXene-based architectures receive tremendous attention for various potential applications. However, conventional methods are incapable of producing customized structures with controllable functionality and performances. Herein, we demonstrate...

materials science, multidisciplinary,chemistry, physical,energy & fuels
Ultrathin Carbon Foams for Effective Electromagnetic Interference Shielding

Yang Li,Bin Shen,Xueliang Pei,Yonggang Zhang,Da Yi,Wentao Zhai,Lihua Zhang,Xingchang Wei,Wenge Zheng

DOI: https://doi.org/10.1016/j.carbon.2016.01.030

IF: 10.9

2016-01-01

Carbon

Abstract:Ultrathin carbon foams with the thickness about 24 mm were fabricated by the pyrolysis of polyimide/graphene composite foams. The addition of graphene was verified to stabilize the porous structure of the foams and accelerate their graphitization process simultaneously. Consequently, the well-defined carbon foams exhibited much higher electromagnetic interference (EMI) shielding effectiveness (SE) up to 24 dB over the frequency range of 8-12 GHz, in comparison with the non-foamed counterparts. The possible mechanism behind the phenomenon was attributed to their enhanced microwave absorption via the internal multiple scattering and reflections. Moreover, the SE could be further improved to 43 and 51 dB by increasing the sample thickness gradually to 51 and 73 mm, respectively. The carbon foams with high thermal stability are very promising in the fabrication of ultrathin EMI shields for thermally harsh applications. (C) 2016 Elsevier Ltd. All rights reserved.
Facile fabrication of lightweight porous FDM-Printed polyethylene/graphene nanocomposites with enhanced interfacial strength for electromagnetic interference shielding

Jingjing Jing,Yu Xiong,Shaohong Shi,Haoran Pei,Yinghong Chen,Philippe Lambin

DOI: https://doi.org/10.1016/j.compscitech.2021.108732

IF: 9.1

2021-05-01

Composites Science and Technology

Abstract:In order to shield the massive electromagnetic perturbations and meet the more and more stringent requirement for advanced electronic equipment, development of diverse, lightweight and high-performance electromagnetic interference (EMI) shielding materials is urgent but still challenging. Herein, the facile and green method which combines fused deposition modeling (FDM) 3D printing, ball milling and microwave (MW) irradiation technology was proposed to fabricate exfoliated graphene nanoplatelets (GNPs) incorporated liner low density polyethylene (LLDPE) nanocomposite lightweight parts with porous and complex geometry structure. FDM 3D printing possesses high flexibility for structure design, which can significantly broaden the application of materials in various fields. Benefiting from design of a unique porous lamellar structure, the printed LLDPE/GNPs nanocomposite parts can achieve a prominent EMI shielding effectiveness (SE) of ∼32.4 dB (with thickness-normalized specific EMI SE (SSE/t) of 318 dB cm2 g−1) in the range of 8.2-12.4 GHz. This remarkable characteristic is due to internal multiple reflections and absorption. In addition, the specific FDM 3D-printed porous parts prepared by our strategy exhibit a relatively higher EMI SE at a lower density than those lightweight EMI shields in literatures. The use of MW irradiation technology improves mechanical properties, especially for the interfacial bonding strength between filaments. More importantly, this strategy is highly favorable for the fabrication of lightweight porous EMI shields with tailorable and optimized shape/structure, which could be expected to be applied in aerospace fields, portable electronic devices, smart devices and so on.

materials science, composites
Emulsion‐Based Multiscale Structural Design Realizes Lightweight and Superelastic Graphene Aerogels for Electromagnetic Interference Shielding

Yiman Zhang,Peng Min,Guoyao Yue,Bochao Niu,Lulu Li,Zhong‐Zhen Yu,Hao‐Bin Zhang

DOI: https://doi.org/10.1002/smll.202405950

IF: 13.3

2024-09-05

Small

Abstract:Superelastic graphene aerogels with multiscale structural tunability are fabricated by an emulsion‐based approach, followed by freeze‐drying and thermal annealing. The aerogels with ultralow density (3.0 mg cm−3) can withstand 90% of reversible compressive strain and exhibit air‐caliber thermal insulation and high electromagnetic interference shielding effectiveness of 75.0 dB in X‐band. Ultralight graphene aerogels with high electrical conductivity and superelasticity are demanded yet difficult to produce. A versatile emulsion‐based approach is demonstrate to optimize multiscale structure of lightweight, elastic, and conductive graphene aerogels. By constructing Pickering emulsion using graphene oxide (GO), poly (amic acid) (PAA), and octadeyl amine (ODA), micron‐level close‐pore structure is realized while thermal shrinkage mismatch between GO and PAA creates numerous nanowrinkles during thermal annealing. GO nanosheets are bridged by PAA‐derived carbon, enhancing the structural integrity at molecular level. These multiscale structural features facilitate rapid electron transport and efficient load transfer, conferring graphene aerogels with intriguing mechanical and electromagnetic interference (EMI) shielding properties. The emulsion‐based graphene aerogel with an ultralow density of ≈3.0 mg cm−3 integrates outstanding electrical conductivity, air‐caliber thermal insulation, high EMI shielding effectiveness of 75.0 dB, and 90% strain compressibility with superb fatigue resistance. Intriguingly, thanks to the gel‐like rheological behavior of the emulsion, ultralight graphene scaffolds with programmable geometries are obtained by 3D printing. This work provides a general approach for the preparation of ultralight and superelastic graphene aerogels with excellent EMI shielding properties, showing broad application prospects in various fields.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
3D graphene/ carbon nanotubes/ polydimethylsiloxane composites as high-performance electromagnetic shielding material in X-band

Hui Jia,Qing-Qiang Kong,Zhuo Liu,Xian-Xian Wei,Xiao-Ming Li,Jing-Peng Chen,Feng Li,Xiao Yang,Guo-Hua Sun,Cheng-Meng Chen

DOI: https://doi.org/10.1016/j.compositesa.2019.105712

2020-02-01

Abstract:High-performance electromagnetic shielding materials are highly desired due to the radiation and interference problems of electronic equipment. In this work, a flexible graphene/multi-walled carbon nanotubes (MWCNTs)/Polydimethylsiloxane (PDMS) electromagnetic shielding composite is fabricated with 3D graphene/MWCNTs foam as electrical conductive skeleton. The structure and composition evolution of foams are studied during the carbonization process from 1200 to 1600 oC and the graphitization of ultra-high temperature (2800 oC). With the removal of functional groups, the repair of defects enhances the ohmic loss while the polarization loss is reduced. An optimal electromagnetic interference shielding effectiveness(EMI SE)is found with an EMI SE of 54.43 dB at 1400 oC. Moreover, compared to pure PDMS, the thermal conductivity of the composites is increased by 193% and the compressive strength is improved from 1.40 MPa to 1.94 MPa. This contribution provides a guidance for designing high-performance carbon-based electromagnetic shielding materials.
Slippery Graphene-Bridging Liquid Metal Layered Heterostructure Nanocomposite for Stable High-Performance Electromagnetic Interference Shielding

Yue Sun,Xiao Han,Pu Guo,Ziyuan Chai,Jingyi Yue,Yunting Su,Shengda Tan,Xu Sun,Lei Jiang,Liping Heng

DOI: https://doi.org/10.1021/acsnano.3c02975

IF: 17.1

2023-06-30

ACS Nano

Abstract:Gallium-based liquid metal (LM) with intriguing high electrical conductivity and room-temperature fluidity has attracted substantial attention for its potential application in flexible electromagnetic interference (EMI) shielding. However, the EMI shielding performance of the existing LM-based composites is unsatisfying due to the irreconcilable contradiction between high EMI shielding efficiency (SE) and low thickness. In addition, the research on environmentally stable EMI shielding material...

materials science, multidisciplinary,chemistry, physical,nanoscience & nanotechnology
Facile preparation of large-scale expanded graphite/polydimethylsiloxane composites for highly-efficient electromagnetic interference shielding

Fei Zhang,Chuanbing Li,Yinhang Zhang,Yuxuan Sun,Xuming Yao,Lei Guo,Jinyi Wu,Kun Dai,Jiatai Wu,Qingbin Zheng

DOI: https://doi.org/10.1039/d2ta06263a

IF: 11.9

2022-10-21

Journal of Materials Chemistry A

Abstract:Lightweight, flexible and low-cost electromagnetic interference (EMI) shielding materials with high shielding effectiveness (SE) have attracted considerable attention for next-generation portable and wearable electronics. In this work, high performance polymer composite-based EMI shielding materials are fabricated by utilizing highly oriented graphite frameworks (HOGFs) constructed via a facile intercalation–expansion of commercially available graphite papers to offer a simple and efficient approach for large-scale production. The obtained highly oriented conductive HOGF/polydimethylsiloxane (HOGF/PDMS) composites exhibit a remarkable conductivity of 21 000 S m −1 and a super-high EMI shielding value of over 96 dB in the X-band (8.2 to 12.4 GHZ) due to the multiple internal reflections caused by the long-range ordered stacking of graphite sheets. In consideration of the excellent conductivity and high electromagnetic shielding performance, along with ease and economy of mass production, the HOGF/PDMS composites demonstrate promising potential for next-generation EMI shielding materials.

materials science, multidisciplinary,chemistry, physical,energy & fuels
Pressure-Induced Self-Interlocked Structures for Expanded Graphite Composite Papers Achieving Prominent EMI Shielding Effectiveness and Outstanding Thermal Conductivities

Hui Zhao,Jin Yun,Yali Zhang,Kunpeng Ruan,Yinsen Huang,Yaping Zheng,Lixin Chen,Junwei Gu

DOI: https://doi.org/10.1021/acsami.1c22950

2022-01-07

Abstract:High-performance films via layer-by-layer assembly of two-dimensional (2D) materials would provide all possibilities for the development of modern integrated electronics. However, the stacked structure between nanosheets and large-scale fabrication still remain a great challenge. Herein, Fe3O4/expanded graphite (EG) papers are fabricated via in situ oxidation of ferrocene onto EG nanosheets, followed by a continuous roll-in process. Upon mechanical compaction, the self-interlocked structures driven by close overlapping and hooking of nanosheets in Fe3O4/EG (FG) composites remarkably facilitate the construction of phonon and electron transmission channels and improve mechanical strength. FG papers exhibit prominent shielding effectiveness (67.1 dB at ∼100 μm) with enhanced absorptivity (∼0.1, surpassing lots of conductive film materials), stemming from the synergistic effect of electrical and magnetic properties. Also, the electromagnetic interference (EMI) shielding performance shows prominent reliability after bending (2000 cycles) and ultrasonic treatment (30 min). The corresponding tensile strength reaches 35.8 MPa; meanwhile, the corresponding in-plane thermal conductivity coefficient is as high as 191.7 W/(m·K), which can rapidly and efficiently accelerate heat dissipation. In particular, FG papers also reveal rapid response, controllable, and highly stable Joule heating performance and present promising prospects in the fields of radiation-proof clothing, flexible heaters, portable wearable devices, and aerospace.

materials science, multidisciplinary,nanoscience & nanotechnology
Carbon Nanotube–Multilayered Graphene Edge Plane Core–Shell Hybrid Foams for Ultrahigh‐Performance Electromagnetic‐Interference Shielding

Qiang Song,Fang Ye,Xiaowei Yin,Wei Li,Hejun Li,Yongsheng Liu,Kezhi Li,Keyu Xie,Xuanhua Li,Qiangang Fu,Laifei Cheng,Litong Zhang,Bingqing Wei

DOI: https://doi.org/10.1002/adma.201701583

IF: 29.4

2017-06-19

Advanced Materials

Abstract:Materials with an ultralow density and ultrahigh electromagnetic-interference (EMI)-shielding performance are highly desirable in fields of aerospace, portable electronics, and so on. Theoretical work predicts that 3D carbon nanotube (CNT)/graphene hybrids are one of the most promising lightweight EMI shielding materials, owing to their unique nanostructures and extraordinary electronic properties. Herein, for the first time, a lightweight, flexible, and conductive CNT-multilayered graphene edge plane (MLGEP) core-shell hybrid foam is fabricated using chemical vapor deposition. MLGEPs are seamlessly grown on the CNTs, and the hybrid foam exhibits excellent EMI shielding effectiveness which exceeds 38.4 or 47.5 dB in X-band at 1.6 mm, while the density is merely 0.0058 or 0.0089 g cm-3 , respectively, which far surpasses the best values of reported carbon-based composite materials. The grafted MLGEPs on CNTs can obviously enhance the penetration losses of microwaves in foams, leading to a greatly improved EMI shielding performance. In addition, the CNT-MLGEP hybrids also exhibit a great potential as nano-reinforcements for fabricating high-strength polymer-based composites. The results provide an alternative approach to fully explore the potentials of CNT and graphene, for developing advanced multifunctional materials.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Multifunctional Flexible AgNW/MXene/PDMS Composite Films for Efficient Electromagnetic Interference Shielding and Strain Sensing

Xiaolong Bian,Zhonglin Yang,Tao Zhang,Jiewen Yu,Gaopeng Xu,An Chen,Qingquan He,Jun Pan

DOI: https://doi.org/10.1021/acsami.3c08093

IF: 9.5

2023-08-24

ACS Applied Materials & Interfaces

Abstract:With the rapid development of electronic information technology, composite materials with outstanding performance in terms of electromagnetic interference (EMI) shielding and strain sensing are crucial for next-generation smart wearable electronic devices. However, the fabrication of flexible composite films with dual functionality remains a significant challenge. Herein, multifunctional flexible composite films with exciting EMI shielding and strain sensing properties were constructed using a...

materials science, multidisciplinary,nanoscience & nanotechnology
3D Expanded Graphite Frameworks for Dual-Functional Polymer Composites with Exceptional Thermal Conductive and Electromagnetic Interference Shielding Capabilities

Chao Liu,Wei Wu,Qiming Chen,Yi Wang,Sufei Cui,Hong Yang

DOI: https://doi.org/10.1021/acsaelm.1c01120

IF: 4.494

2022-01-24

ACS Applied Electronic Materials

Abstract:At present, dual-functional polymer composites possessing excellent thermal conductivity and high electromagnetic interference shielding effectiveness (EMI SE) are largely demanded in the synchronous thermal and EM wave management of advanced microelectronic devices. Herein, we report an annealed 3D expanded graphite (A-3D-EG) framework featuring high-quality continuous carbon architectures that can serve as high-throughput phonon and electron transmission pathways to effectively elevate the thermal conductivity and EMI shielding performance of polymers. This framework is fabricated via hydrothermally treating the aqueous slurry containing EG and GO fillers, followed by freezing-drying and annealing treatment at 1600 °C for 2 h. As a result, the polydimethylsiloxane composite filled with A-3D-EG reveals an outstanding thermal conductivity of 12.95 Wm–1K–1 and a high EMI SE of 85.0 dB at a low filler content of 31.9 wt %. This work demonstrates that A-3D-EG has enormous utilization potential in fabricating polymer composites simultaneously with high thermal conductivity and outstanding EMI shielding capability, which can be utilized in aerospace, telecommunications, and mobile electronic devices.

materials science, multidisciplinary,engineering, electrical & electronic
Intercalation: Constructing Nanolaminated Reduced Graphene Oxide/Silica Ceramics for Lightweight and Mechanically Reliable Electromagnetic Interference Shielding Applications

Yujia Huang,Kouichi Yasuda,Chunlei Wan

DOI: https://doi.org/10.1021/acsami.0c15193

IF: 9.5

2020-01-01

ACS Applied Materials & Interfaces

Abstract:There is a critical need to develop lightweight and mechanically reliable materials for electromagnetic interference (EMI) shielding applications in the harsh environment. In this study, we propose a low-density (∼2.2 g/cm3) reduced graphene oxide (rGO)/silica ceramic with multilayer rGO sheets parallelly aligned inside the silica matrix through a new intercalation strategy. The parallel rGO sheets lead to outstanding EMI shielding effectiveness values of 29-33 dB in the X-band, owing to the interlayer multiple reflections of the electromagnetic wave. Meanwhile, the parallel rGO sheets elevate the flexural strength by 110-130% and improve the fracture toughness by 100-130% compared with the monolithic silica by capturing and deflecting the propagating cracks. The nanolaminated structure constructed by the intercalation approach can effectively break the trade-off between mechanical properties and EMI shielding performances in the graphene/ceramic composites, thus opening up new opportunities in the lightweight and mechanically reliable EMI applications.
3D cross-linked graphene or/and MXene based nanomaterials for electromagnetic wave absorbing and shielding

Yanhong Lu,Suling Zhang,Meiyu He,Lei Wei,Yu Chen,Ruina Liu

DOI: https://doi.org/10.1016/j.carbon.2021.01.161

IF: 10.9

2021-06-01

Carbon

Abstract:With the rapid digitalization and technological advancements of the modern society, the seriously increasing electromagnetic pollution has created stronger demand for advanced electromagnetic wave shielding and absorbing materials in both civilian and military fields. Multifunctional materials with ultra-lightweight, wide bandwidth, highly flexible and robustness are the future development direction to meet the applications. Graphene and MXene, as two typical 2D nanomaterials, have attracted considerable interests for the electromagnetic wave shielding and absorbing materials. More importantly, three dimensional (3D) cross-linked graphene or/and MXene based materials, where graphene or/and MXene sheets are interconnected into a macroscopic monolithic bulk material, can achieve excellent electromagnetic interference (EMI) shielding and microwave absorption (MA) performance, together with lightweight, exceptional mechanical properties and so on. This review addresses the construction methods of graphene and MXene based 3D cross-linked materials, and the effects of different fabrication methods toward the structure and EMI shielding and/or MA properties are discussed. Additionally, some perceptions and discussions are proposed for the future studies.

materials science, multidisciplinary,chemistry, physical
Graphene aerogel films with expansion enhancement effect of high-performance electromagnetic interference shielding

Jiabin Xi,Youliang Li,Erzhen Zhou,Yingjun Liu,Weiwei Gao,Yan Guo,Ji Ying,Zichen Chen,Guogui Chen,Chao Gao

DOI: https://doi.org/10.1016/j.carbon.2018.04.041

IF: 10.9

2018-01-01

Carbon

Abstract:Lightweight and flexible materials with high electromagnetic interference (EMI) shielding performance are highly desirable in numerous occasions to prevent interference between electronic devices. Here, we designed graphene aerogel films (GAF) with multilayer structure, which showed low density (0.02 g cm−3), high flexibility and excellent shielding effectiveness (SE). SE reaches ∼135 dB in 0.1–3 GHz at thickness of 1.4 mm, and shows an uptrend from 65 to 105 dB in 2–18 GHz at thickness of 120 μm. In depth study reveal the excellent shielding performance is attributed to expansion enhancement effect, that shielding effectiveness can be significantly improved by expansion in an individual identical substance. The design of GAFs and the discovery of EEE open the avenue to lightweight materials with high EMI shielding performance.
Ultrastrong Nanopapers with Aramid Nanofibers and Silver Nanowires Reinforced by Cellulose Nanofibril-Assisted Dispersed Graphene Nanoplates for Superior Electromagnetic Interference Shielding

Fugang Hu,Minghong Kui,Jinsong Zeng,Pengfei Li,Tianguang Wang,Jinpeng Li,Bin Wang,Chen Wu,Kefu Chen

DOI: https://doi.org/10.1021/acsnano.4c09462

IF: 17.1

2024-09-04

ACS Nano

Abstract:High-strength, lightweight, ultrathin, and flexible electromagnetic interference (EMI) shielding materials with a high shielding effectiveness (SE) are essential for modern integrated electronics. Herein, cellulose nanofibrils (CNFs) are employed to homogeneously disperse graphene nanoplates (GNPs) into an aramid nanofiber (ANF) network and silver nanowire (AgNW) network, respectively, producing high-performance nanopapers. These nanopapers, featuring nacre-mimetic microstructures and layered architectures, exhibited high tensile strength (601.11 MPa) and good toughness (103.56 MJ m-3) with a thickness of only 24.58 μm. Their specific tensile strength reaches 447.59 MPa·g-1·cm3, which is 1.74 times that of titanium alloys (257 MPa·g-1·cm3). The AgNW/GNP composite conductive layers exhibit an electrical conductivity of 12010.00 S cm-1, providing the nanopapers with great EMI shielding performance, achieving an EMI SE of 63.87 dB and an EMI SE/t of 25978.80 dB cm-1. The nanopapers also show reliable durability, retaining a tensile strength of 500.96 MPa and an EMI SE of 57.59 dB after 120,000 folding cycles. Additionally, they have a good electrical heating performance with a fast response time, low driving voltage, effective deicing capability, and reliable heating capacity in water. This work presents a strategy to develop a high-performance nanopaper, showing great potential for applications in electromagnetic compatibility, national defense, smart electronics, and human health.
Shear-Induced Fabrication of Cellulose Nanofibril/Liquid Metal Nanocomposite Films for Flexible Electromagnetic Interference Shielding and Thermal Management

Ning Ren,Yusen Ai,Ning Yue,Mei Cui,Renliang Huang,Wei Qi,Rongxin Su

DOI: https://doi.org/10.1021/acsami.4c01220

IF: 9.5

2024-03-22

ACS Applied Materials & Interfaces

Abstract:To address electromagnetic interference (EMI) pollution in modern society, the development of ultrathin, high-performance, and highly stable EMI shielding materials is highly desired. Liquid metal (LM) based conductive materials have received enormous amounts of attention. However, the processing approach of LM/polymer composites represents great challenges due to the high surface tension and cohesive energy of LMs. In this study, we develop a universal one-step fabrication strategy to directly...

materials science, multidisciplinary,nanoscience & nanotechnology
Multispectral electromagnetic shielding using ultra-thin metal-metal oxide decorated hybrid nanofiber membranes

Dayong He,Nan Zhang,Aamir Iqbal,Yuying Ma,Xiaofeng Lu,Zhen-An Qiao,Ji-Hong Yu,Hongbo Xu,Wei Wang,Rui Zhao,Xiaofeng Li,Zhiqiang Zhou,Changxian Jin,Chong Min Koo,Ce Wang

DOI: https://doi.org/10.1038/s43246-021-00205-3

2021-09-24

Communications Materials

Abstract:Abstract Lightweight shielding materials that can protect devices against undesirable multispectral electromagnetic waves are critical in electronic, medical, military, and aerospace applications. However, the existing shielding materials are heavyweight and work only in a narrow frequency-range. In this work, we developed metal–metal oxide Ag-WO 3 decorated polymeric nanofiber hybrid membranes with versatile multispectral electromagnetic shielding abilities for practical applications. The Ag-WO 3 hybrid provides multiple functions, such as excellent metallic conductivity provided by silver, high photoelectric effect and low thermal conductivity arising from the high atomic number in WO 3 , and strong infrared energy absorbing capability caused by a designed Schottky barrier interface between Ag and WO 3 . Additionally, the nanofibrous hybrid membrane structure provides high surface area, good air permeability, and robust mechanical strength and durability. These highly conductive, lightweight, ultrathin, and flexible membranes exhibit efficient microwave electromagnetic interference shielding of 92.3 dB at a thickness of ~42 μm in 8–26.5 GHz frequency range, 0.75–0.5 emissivity for near- to far-field infrared bands, and 32.03% attenuation for X-rays of 30 keV at 0.24 mm thickness, indicating their potential for shielding against large-scale multispectral electromagnetic waves from low-frequency microwaves to high-frequency X-rays.
Lightweight and Flexible Cotton Aerogel Composites for Electromagnetic Absorption and Shielding Applications

Yan Cheng,Huanqin Zhao,Hualiang Lv,Tengfei Shi,Guangbin Ji,Yanglong Hou

DOI: https://doi.org/10.1002/aelm.201900796

IF: 6.2

2019-11-18

Advanced Electronic Materials

Abstract:Currently, a versatile route is urgently required to achieve excellent electromagnetic wave (EMW) absorption and shielding functions simultaneously. A lightweight, flexible and sustainable 3D framework aerogel is designed to reach this goal, which is assembled by unique "1D‐1D" combination, nanoscale carbon nanotubes (CNTs) grown on microscale carbon fiber. EM absorption requires appropriate conductivity of filler to acquire moderate permittivity. On the contrary, EM shielding requires great conductivity to reflect most of the incident EMW. Based on this design concept, the change of electric conductivity of as‐obtained samples through in situ regulation of the growth state of CNTs is successfully controlled. When the CNTs are short and curly, the optimized conductivity favors excellent microwave absorption with wide absorption bandwidth of 5.08 GHz at only 1.6 mm. When the CNTs are long and straight, the increased conductivity is clearly boosted with 29.8 dB EM shielding effectiveness. This elaborate architecture and controlled CNT growth allow the designed 3D framework aerogel to be applied in both EM wave absorption and shielding. This conductivity tunable route gives inspiration for fabricating other efficient EM absorption and shielding devices.

materials science, multidisciplinary,physics, applied,nanoscience & nanotechnology

A New Strategy of 3D Printing Lightweight Lamellar Graphene Aerogels for Electromagnetic Interference Shielding and Piezoresistive Sensor Applications

Lightweight Microwire/graphene/silicone Rubber Composites for Efficient Electromagnetic Interference Shielding and Low Microwave Reflectivity

Ultralight, Conductive Ti3C2Tx MXene/PEDOT:PSS Hybrid Aerogels for Electromagnetic Interference Shielding Dominated by the Absorption Mechanism

3D printing of resilient, lightweight and conductive MXene/ reduced graphene oxide architectures for broadband Electromagnetic Interference shielding

Ultrathin Carbon Foams for Effective Electromagnetic Interference Shielding

Facile fabrication of lightweight porous FDM-Printed polyethylene/graphene nanocomposites with enhanced interfacial strength for electromagnetic interference shielding

Emulsion‐Based Multiscale Structural Design Realizes Lightweight and Superelastic Graphene Aerogels for Electromagnetic Interference Shielding

3D graphene/ carbon nanotubes/ polydimethylsiloxane composites as high-performance electromagnetic shielding material in X-band

Slippery Graphene-Bridging Liquid Metal Layered Heterostructure Nanocomposite for Stable High-Performance Electromagnetic Interference Shielding

Facile preparation of large-scale expanded graphite/polydimethylsiloxane composites for highly-efficient electromagnetic interference shielding

Pressure-Induced Self-Interlocked Structures for Expanded Graphite Composite Papers Achieving Prominent EMI Shielding Effectiveness and Outstanding Thermal Conductivities

Carbon Nanotube–Multilayered Graphene Edge Plane Core–Shell Hybrid Foams for Ultrahigh‐Performance Electromagnetic‐Interference Shielding

Multifunctional Flexible AgNW/MXene/PDMS Composite Films for Efficient Electromagnetic Interference Shielding and Strain Sensing

3D Expanded Graphite Frameworks for Dual-Functional Polymer Composites with Exceptional Thermal Conductive and Electromagnetic Interference Shielding Capabilities

Intercalation: Constructing Nanolaminated Reduced Graphene Oxide/Silica Ceramics for Lightweight and Mechanically Reliable Electromagnetic Interference Shielding Applications

3D cross-linked graphene or/and MXene based nanomaterials for electromagnetic wave absorbing and shielding

Graphene aerogel films with expansion enhancement effect of high-performance electromagnetic interference shielding

Ultrastrong Nanopapers with Aramid Nanofibers and Silver Nanowires Reinforced by Cellulose Nanofibril-Assisted Dispersed Graphene Nanoplates for Superior Electromagnetic Interference Shielding

Shear-Induced Fabrication of Cellulose Nanofibril/Liquid Metal Nanocomposite Films for Flexible Electromagnetic Interference Shielding and Thermal Management

Multispectral electromagnetic shielding using ultra-thin metal-metal oxide decorated hybrid nanofiber membranes

Lightweight and Flexible Cotton Aerogel Composites for Electromagnetic Absorption and Shielding Applications