Abstract:The redox flow battery (RFB) is one of the most promising technologies for stationary energy storage. It consists of a voltaic cell whose electrolytes are stored in tanks outside the system. Whilst the chemistries of the anodic and cathodic electrolytes define the energy density of a RFB system, its power density is determined primarily by its electrodes. These are typically porous carbon media on the surface of which the redox reactions occur. They are a critical component since they require a detailed engineering of electrocatalytically active surface area and mass transport. Still today, they remain the main cause of RFB low power density. In this work, we are showing a novel deposition method to improve the performance of commercially available carbon paper already used in RFB. The gain is thanks to the deposition of turbostratic carbon nano-onion (TCNO) nanoparticles on the carbon fibers of the paper. This process is performed with a proprietary technology called NanoJeD: a CVD in supersonic flow, which promises easy industrial scalability and a fine tunability of the nanoparticle properties. Moreover, with this system is possible to deposit over any substrate. NanoJeD consists in two chambers separated by a high aspect ratio slit. A precursor gas is injected through a porous plug from the top and a vacuum system is connected from the bottom. The slit allows the establishment of a high-pressure ratio between the two chambers and hence the formation of a supersonic jet. The precursor gas, a mixture of Argon (98.4%) and Acetylene (1.6%) flows between two electrodes where a radio frequency (RF) signal is fed (13.56 MHz). The RF ignites a non-thermal plasma in which the precursor molecules are ionized and dissociated into radicals, which polymerize forming hydrogenated carbon clusters and nanoparticles (NPs) of different sizes. Once formed, NPs are dragged through the slit by the gas stream and finally impact on the substrate. Therefore, it is possible to achieve a high throughput (500 mg h -1 ) and to deposit on a large area of 100 cm 2 while precisely controlling the properties of the film. The resulting film has hundreds of squared meters per gram of surface area. For TCNO formation, the NP film is further annealed in vacuum at 1000°C for 2 hours. Using in situ transmission electron microscopy (TEM) and energy electron loss spectroscopy (EELS), we were able to visualize the progression of graphitization and changes in structural properties during annealing. The graphitization process starts in the outer layer and proceeds into the interior of the particle. The geometrical constrains of the NP (average diameter of 20nm) and shrinkage of the NP, allow the formation of curved, turbostratic, defective graphitic sheets. UV photoelectron spectroscopy (UPS) and Raman spectroscopy performed ex-situ allow the analysis of valence bands and structural defects. The high presence of defects and general disorder structure are accompanied with a remarkable increase in catalytic activity. Moreover, the annealing process leads to the sintering of the nanoparticles and the formation of an interface between the carbon fibre and the nanoparticles, as demonstrated by the increased thermal stability tested by. Both phenomena improve the adhesion between nanoparticles and with the surface, making the electrode suitable to be adopted in fluxed systems. The TCNO deposited on a carbon paper was tested as electrode in a Vanadium RFB. The kinetic activity and electrochemical properties were tested via in-situ Raman and in a three-electrode cell set-up. The results reveal an increased kinetic activity with respect to the untreated paper. Using in situ Raman we were able to show differences in redox mechanism between TCNO and bare carbon paper. A chronoamperometry test was used to obtain the transfer coefficient from a Tafel plot. These studies allow the correlation of the catalytic activity with the defectiveness of the TCNO nanoparticle. Vanadium RFB full cell measurements of the TCNO electrode show a drastic increase in performance, reaching an energy efficiency of 70.8% and 86.2% at current densities of 600 mA cm -2 and 200 mA cm -2 , respectively. The electrolyte utilisation for these current densities is 59% for the former and 80% for the latter. To investigate the chemical and mechanical stability a stability test was performed. Results showed a low degradation rate of 0.004% EE per cycle. Moreover, TCNO can be used for other electrochemical applications only by adjusting the deposition and annealing parameters.

Increased Current Density of a Redox Flow Battery with a Carbon Paper Partially Modified by Porous Carbon Nanofibers

Highly Active Electrode With Efficiently Added Surface Oxygen Groups for a Vanadium Redox Flow Battery

Nanoscopic and Macro-Porous Carbon Nano-foam Electrodes with Improved Mass Transport for Vanadium Redox Flow Batteries

Enhanced Performance of an All-Vanadium Redox Flow Battery Employing Graphene Modified Carbon Paper Electrodes

Highly active nitrogen-phosphorus co-doped carbon fiber@graphite felt electrode for high-performance vanadium redox flow battery

Morphological Properties and Electrochemical Performance for Compressed Carbon-fiber Electrodes in Redox Flow Batteries

Superior electrocatalytic performance of porous, graphitic, and oxygen-functionalized carbon nanofiber as bifunctional electrode for vanadium redox flow battery

Multiphysics Simulation of Multi-layered Fibrous Electrodes for the Vanadium Redox Flow Battery

Activated Carbon Fiber Paper Based Electrodes with High Electrocatalytic Activity for Vanadium Flow Batteries with Improved Power Density.

Highly porous carbon nanofiber electrodes for vanadium redox flow batteries

A composite electrode with gradient pores for high-performance aqueous redox flow batteries

Sponge‐Like Microfiber Electrodes for High‐Performance Redox Flow Batteries

Turbostratic Carbon Nano Onion Electrode for High Power Density Vanadium Redox Flow Battery

Vanadium Redox Flow Battery Using an N-Doped Porous Carbon-Coated Positive Electrode Derived from Zeolitic Imidazolate Framework-8-Coated Graphite Felt

Quantifying effects of surface morphology and functional groups of carbon fibers on mass transfer coefficient in vanadium redox flow batteries

Highly Active Hollow Porous Carbon Spheres@Graphite Felt Composite Electrode for High Power Density Vanadium Flow Batteries

Densely Populated Bismuth Nanosphere Semi‐Embedded Carbon Felt for Ultrahigh‐Rate and Stable Vanadium Redox Flow Batteries

Effect of nanofluidic electrolyte on the electrochemically enhanced long‐term efficiency of vanadium redox flow battery

High‐performance Porous Electrodes for Flow Batteries: Improvements of Specific Surface Areas and Reaction Kinetics

Enhancement of the Electrode Activity of the Vanadium Redox Flow Battery by Higher Crystallinity of Carbon Matrix Using Seamless and Consecutive-porous Carbon Materials