Abstract:Lithium–sulfur (Li–S) batteries are severely hindered by the low sulfur utilization and short cycling life, especially at high rates. One of the effective solutions to address these problems is to improve the sulfiphilicity of lithium polysulfides (LiPSs) and the lithiophilicity of the lithium anode. However, it is a great challenge to simultaneously optimize both aspects. Herein, by incorporating the merits of strong absorbability and high conductivity of SnS with good catalytic capability of ZnS, a ZnS-SnS heterojunction coated with a polydopamine-derived N-doped carbon shell (denoted as ) with uniform cubic morphology was obtained and compared with the ZnS-SnS2@NC heterostructure and its single-component counterparts ( and SnS2@NC). Theoretical calculations, ex situ XANES, and in situ Raman spectrum were utilized to elucidate rapid anchoring-diffusion-transformation of LiPSs, inhibition of the shuttling effect, and improvement of the sulfur electrochemistry of bimetal ZnS-SnS heterostructure at the molecular level. When applied as a modification layer coated on the separator, the cell with optimized lithiophilicity and sulfiphilicity enables desirable sulfur electrochemistry, including high reversibility of 1149 mAh g–1 for 300 cycles at 0.2 C, high rate performance of 661 mAh g–1 at 10 C, and long cycle life with a low fading rate of 0.0126% each cycle after 2000 cycles at 4 C. Furthermore, a favorable areal capacity of 8.27 mAh cm–2 is maintained under high sulfur mass loading of 10.3 mg cm–2. This work furnishes a feasible scheme to the rational design of bimetal sulfides heterostructures and boosts the development of other electrochemical applications.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsnano.1c00270?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsnano.1c00270</a>.Additional experimental sections (materials synthesis, characterizations, and DFT calculations); SEM, TEM, XRD, TG, XPS, BET, and XANES characterizations of the samples; CV curves; discharge–charge profiles and cycle performance of various electrodes; in situ Raman tests; optimized geometries of LiPSs; Tables S1–S6: Li+ diffusion rates, EIS fitting, and comparisons of electrochemical performance (<a class="ext-link" href="/doi/suppl/10.1021/acsnano.1c00270/suppl_file/nn1c00270_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Rational design and superfast production of biomimetic, calendering-compatible, catalytic, sulfur-rich secondary particles for advanced lithium-sulfur batteries

Feasible Catalytic-Insoluble Strategy Enabled by Sulfurized Polyacrylonitrile with In Situ Built Electrocatalysts for Ultrastable Lithium–Sulfur Batteries

Mass Production of Customizable Core–Shell Active Materials in Seconds by Nano‐Vapor Deposition for Advancing Lithium Sulfur Battery

Rationally Design a Sulfur Cathode with Solid‐Phase Conversion Mechanism for High Cycle‐Stable Li–S Batteries

Aligned sulfur-deficient ZnS1−x nanotube arrays as efficient catalyzer for high-performance lithium/sulfur batteries

Enhanced Electrochemical Kinetics with Highly Dispersed Conductive and Electrocatalytic Mediators for Lithium–Sulfur Batteries

A strategy to achieve high loading and high energy density Li-S batteries

Fast conversion and controlled deposition of lithium (poly)sulfides in lithium-sulfur batteries using high-loading cobalt single atoms

Programmed Design of a Lithium–Sulfur Battery Cathode by Integrating Functional Units

Flexible and Self-Supported Sulfur Cathode for High-Energy-Density Lithium-Sulfur Batteries

Establishing highly efficient absorptive and catalytic network for depolarized high-stability lithium-sulfur batteries

A compact 3D interconnected sulfur cathode for high-energy, high-power and long-life lithium-sulfur batteries

Efficient and Homogenous Precipitation of Sulfur Within a 3D Electrospun Heterocatalytic Rutile/Anatase TiO2-x Framework in Lithium–Sulfur Batteries

Design Zwitterionic Amorphous Conjugated Micro‐/Mesoporous Polymer Assembled Nanotentacle as Highly Efficient Sulfur Electrocatalyst for Lithium‐Sulfur Batteries

ZnS-SnS@NC Heterostructure as Robust Lithiophilicity and Sulfiphilicity Mediator toward High-Rate and Long-Life Lithium–Sulfur Batteries

Catalytic Interfaces‐Enriched Hybrid Hollow Spheres Sulfur Host for Advanced Li–S Batteries

Integrated Design of Interlayer/Current-Collector: Heteronanowires Decorated Carbon Microtube Fabric for High-Loading and Lean-Electrolyte Lithium-Sulfur Batteries

Integration of nickel phosphide nanodot-enriched 3D graphene-like carbon with carbon fibers as self-supported sulfur hosts for advanced lithium sulfur batteries

Engineering the Conductive Network of Metal Oxide‐Based Sulfur Cathode toward Efficient and Longevous Lithium–Sulfur Batteries

Engineering single-atom catalysts as multifunctional polysulfide and lithium regulators toward kinetically accelerated and durable lithium-sulfur batteries

Self-templating synthesis of prismatic-like N-doped carbon tubes embedded with Fe3O4 as a high-efficiency polysulfide-anchoring-conversion mediator for high performance lithium-sulfur batteries