Abstract:Life cycle assessment has confirmed the effectiveness of carbon fiber reinforced polymer-matrix composite (CFRP) materials’ application in CO2 reduction as well as in weight reduction (JCMA in 2008). Thanks to these strong and ultimate lightweight structure materials, burdens imposed by vehicles on environment nowadays could be significantly relieved. However, speedy manufacturing and recycle technology have to be established to apply to mass-production of automobiles using CFRP components. It is estimated that 3,000 t of CFRP scrap being generated annually in Europe and the USA. Some 6,000–8,000 commercial planes are expected to reach end-of-life dismantlement by 2030 (McConnell in Reinf Plast 54(2):33–37, 2010). Historically, CFRP waste has been disposed of in landfills. Since 2004, most European countries have banned the landfill disposal of CFRP waste. Future EU regulations will be imposed on the recycling of end-of-life aircraft along the same lines as those for scrapped vehicles. Besides, high cost of the carbon fibers is likely to be one of the strongest drivers for recycling of CFRP waste if an economic and environmentally friendly technology can be developed to provide a potential sustainable resource of reusable fibers. Numerous recycling approaches have been proposed and investigated: microwave treatment (Lester et al. in Mater Res Bull 39(10):1549–1556, 2004), vacuum pyrolysis (Cunliffe et al. in J Anal Appl Pyrol 70(2):315–338, 2003), chemical solvolysis (Piñero-Hernanz et al. in J Supercrit Fluids 46(1):83–92, 2008; Goto in J Supercrit Fluids 47(3):500–507, 2009), as well as hydro-thermolysis (Piñero-Hernanz et al. in Compos A 39(3):454–461, 2008). Steam thermolysis, a combination of vacuum pyrolysis and mild gasification, has been studied in our laboratory. The process takes place under medium temperatures (until 600 °C) and atmospheric pressure. By using superheated steam as a soft oxidant, the polymer matrix can be converted into lower molecular weight hydrocarbons, CO and CO2 without seriously reducing the mechanical properties of the carbon fiber reinforcement. The steam-thermolysis has been studied and confirmed efficient in treating epoxy based CFRP materials at bench scale. In order to optimize the process, an experimental design has been carried out by using Taguchi method at semi-industrial scale. Initially, an orthogonal array testing was applied to determine the potential influence of the operational parameters on the decomposition rate of the polymer matrix as wall as on the mechanical property of the reclaimed carbon fibers. Three operational parameters at two levels each (target temperature, isothermal dwell time and steam flow-rate) were identified and tested. During the test, some 100 g epoxy based CFRP scrap samples were loaded into a thermal reactor preheated till desired temperature. The steam is flushed with a flow of nitrogen throughout the test to avoid oxidative side reactions. Additional tests were also conducted to complete and validate the results.

Using Thermogravimetric Analysis to Determine Carbon Fiber Weight Percentage of Fiber-Reinforced Plastics

Fibre-volume-fraction measurement of carbon fibre reinforced thermoplastic composites using thermogravimetric analysis

Characterization of Microplastics in Environment by Thermal Gravimetric Analysis Coupled with Fourier Transform Infrared Spectroscopy.

Decomposition Kinetics and Lifetime Estimation of Thermoplastic Composite Materials Reinforced with rCFRP

Fatigue Damage Evaluation of Short Carbon Fiber Reinforced Plastics Based on Phase Information of Thermoelastic Temperature Change

Use of Karl Fischer titration for the localized measurement of water content in FRP composite aircraft parts removed from service

Parameter Optimization of the Steam Thermolysis: A Process to Recover Carbon Fibers from Polymer-Matrix Composites

Thermal Decomposition Kinetics of Basalt Fiber-Reinforced Wood Polymer Composites

Evaluation of the Fracture Toughness of Short Carbon Fiber Reinforced Thermoplastic Composites

Thermomechanical Material Characterization of Polyethylene Terephthalate Glycol with 30% Carbon Fiber for Large-Format Additive Manufacturing of Polymer Structures

Characterisation and composition identification of waste-derived fuels obtained from municipal solid waste using thermogravimetry: A review

Assessment of carbon fiber incorporation effects on overall characteristics and properties of 3D-printed PLA

Pyrolysis Kinetic Study and Reaction Mechanism of Epoxy Glass Fiber Reinforced Plastic by Thermogravimetric Analyzer (TG) and TG–FTIR (Fourier-Transform Infrared) Techniques

Through-thickness frontal polymerization: Process development and optimization

Characterization Approach for Compression Molded Discontinuous Fiber Thermoplastic Composites

A Micromechanical Modeling Approach for the Estimation of the Weathering-Induced Degradation of Wind Turbine Blades

Statistical Analysis of Large Format Additively Manufactured Polyethylene Terephthalate Glycol with 30% Carbon Fiber Tensile Data

The Effect of GFRP Powder on the High and Low-Temperature Properties of Asphalt Mastic

Experimental methods in chemical engineering: Thermogravimetric analysis—TGA

Thermal Recycling Process of Carbon Fibers from Composite Scrap—Characterization of Pyrolysis Conditions and Determination of the Quality of Recovered Fibers