Abstract:This research focuses on 3D printable thermoplastic polyurethane filaments embedded with multi‐walled carbon nanotubes for enhanced strain sensing in large deformations. It explores the electromechanical properties of the filaments, identifying a conductive threshold in the composite material. The study also examines the application of these filaments in flexible structures, particularly for soft robotics and wearable electronics. This study investigates the development of thermoplastic polyurethane (TPU) filaments incorporating multi‐walled carbon nanotubes (MWCNT) to enhance strain‐sensing capabilities. Various MWCNT reinforcement ratios are used to produce customized feedstock for fused filament fabrication (FFF) 3D printing. Mechanical properties and the piezoresistive response of samples printed with these multifunctional filaments are concurrently evaluated. Surface morphology and microstructural observations reveal that higher MWCNT weight percentages increase filament surface roughness and rigidity. The microstructural modifications directly influence the tensile strength and strain energy of the printed samples. The study identifies an apparent percolation threshold within the 10–12 wt.% MWCNT range, indicating the formation of a conductive network. At this threshold, higher gauge factors are achieved at lower strains. A newly introduced Electro‐Mechanical Sensitivity Ratio (ESR) parameter enables the classification of composite behaviors into two distinct zones, offering the ability to tailor self‐sensing structures with on‐demand properties. Finally, flexible structures with proven application in soft robotics and shape morphing are fabricated and tested at different loading conditions to demonstrate the potential applicability of the custom filaments produced. The results highlight a pronounced piezoresistive response and superior load‐bearing performance in the examined structures.

Reprocessable 3D-Printed Conductive Elastomeric Composite Foams for Strain and Gas Sensing

Highly Sensitive Large Strain Cellulose/multiwalled Carbon Nanotubes (mwcnts)/thermoplastic Polyurethane (TPU) Nanocomposite Foams: from Design to Performance Evaluation

High-strength, Flexible and Cycling-Stable Piezo-Resistive Polymeric Foams Derived from Thermoplastic Polyurethane and Multi-Wall Carbon Nanotubes

Preparation of Thermoplastic Polyurethane/Multi-Walled Carbon Nanotubes Composite Foam with High Resilience Performance via Fused Filament Fabrication and CO2 Foaming Technique

3D Printed Multifunctional, Hyperelastic Silicone Rubber Foam

A stretchable flexible strain sensor with high sensitivity and fast response fabricated by embedded 3D printing of the hybrid polydimethylsiloxane/conductive carbon paste composites

3D Printing Mechanically Robust and Transparent Polyurethane Elastomers for Stretchable Electronic Sensors

Fabrication of high sensitivity and stable strain sensors based on composite folded structures via embedded 3D printing

Thermoplastic elastomer composite filaments for strain sensing applications extruded with a fused deposition modelling 3D printer

Selective coaxial ink 3D printing for single-pass fabrication of smart elastomeric foam with embedded stretchable sensor

Tailored and Highly Stretchable Sensor Prepared by Crosslinking an Enhanced 3D Printed UV‐Curable Sacrificial Mold

3D Printed Reduced Graphene Oxide/Elastomer Resin Composite with Structural Modulated Sensitivity for Flexible Strain Sensor

Ultrasensitive Wearable Strain Sensors of 3D Printing Tough and Conductive Hydrogels

3D printing of branched polyurethane with tough mechanical properties for stretchable sensors

Effects of non-covalent interactions on the properties of 3D printed flexible piezoresistive strain sensors of conductive polymer composites

Electrical conductivities and sensing mechanisms of low-temperature 3D printing conductive hydrogels with good sensitivity

Bidirectional and Stretchable Piezoresistive Sensors Enabled by Multimaterial 3D Printing of Carbon Nanotube/Thermoplastic Polyurethane Nanocomposites

A Simple, Low-Cost Conductive Composite Material for 3D Printing of Electronic Sensors

Flexible, recyclable and sensitive piezoresistive sensors enabled by lignin polyurethane-based conductive foam

Fabrication and Characterization of Electrically Conductive 3D Printable TPU/MWCNT Filaments for Strain Sensing in Large Deformation Conditions

Fabrication of Highly Reinforced and Compressible Graphene/Carbon Nanotube Hybrid Foams Via A Facile Self-Assembly Process for Application As Strain Sensors and Beyond