Abstract:In the present research work, an effort has been made to examine the effect of the ERNiCrCoMo-1 filler on solidification mechanism, microstructural characterization, welded joint integrity, and residual stresses of the dissimilar welded joint (DWJ) of martensitic grade P92 steel and Ni-based superalloy Inconel 617 for advanced ultra-supercritical (A-USC) power plant application. Weld joints have been fabricated for V groove geometry by using the multipass gas tungsten arc welding (GTAW) process. The multiple aspects of the welded joint structural integrity have been tested by performing the tensile test, microhardness tests and Charpy impact test. The ERNiCrCoMo-1 weld solidified in austenitic mode with columnar and cellular dendrites in the interior region, while columnar dendrites were observed near the interface region. The unmixed zone (UZ) formation was noticed at the ERNiCrCoMo-1 filler weld and P92 steel interface, while the UZ gets eliminated at Inconel 617 interface. The microstructural observation near the interface showed that migrated grain boundaries were observed frequently near the lower region of the weld metal (WM), while at the interface of the P92 steel and ERNiCrCoMo-1 filler welds, higher density of soft δ ferrite patches for the capping and backing passes were observed. The energy-dispersive spectroscopy (EDS) and X-ray diffraction (XRD) results confirmed the presence of the Cr- and Mo-enriched M 23 C 6 precipitates, Mo-enriched M 6 C and Ti-enriched Ti(C, N) precipitates in the WM. Acceptable mechanical properties were obtained at room temperature. The Charpy impact toughness (CIT) was observed 98 ± 5 J and 108 ± 3 J for WM with V notch at the top and root region, respectively. The dramatic reduction in CIT was after the postweld heat treatment (PWHT) was attributed to the evolution of the carbide particles in interdendritic areas. Tensile strength results of the cross-weld specimen showed the tensile strength value marginally lower than the P92 steel but significantly lower than the Inconel 617 base metal in both as-welded (AW) and PWHT condition along with fracture in the week region of P92 steel. The failure from the region of P92 steel instead of the ERNiCrCoMo-1 filler WM confirmed that the welded joint was safe for A-USC power plants boiler application. A significant heterogeneity in microhardness was seen along the weldments with a peak hardness of 445 ± 8 in P92 CGHAZ and a lower hardness of 181 HV in the peninsula. The increase in microhardness of the WM as a result of PWHT was attributed to the evolution of the carbide particles in the WM. Through thickness residual stresses variation was also measured for both WM and HAZ region and the effect of the PWHT on the magnitude and nature of the residual stresses were also performed. Hence the work provides insight into welding procedure development, microstructural evolution in the WM and HAZ, variation in mechanical properties, and residual stresses variation for the welded joint of P92 steel and Inconel 617 alloy.

Feasibility study of wire arc additive manufactured P91 steel by cold metal transfer deposition

Improving mechanical strength and isotropy for wire-arc additive manufactured 304L stainless steels via controlling arc heat input

Microstructure and Mechanical Properties of 304L Steel Fabricated by Arc Additive Manufacturing

Experimental study on the heat input behavior of wire-arc additively manufactured 316L stainless steel parts for repairing applications

Effect of Groove Design and Post-Weld Heat Treatment on Microstructure and Mechanical Properties of P91 Steel Weld

Mechanical properties of wire arc additive manufactured carbon steel cylindrical component made by cold metal transferred arc welding process

Mechanical, metallurgical, and corrosion investigations on wire arc additively manufactured low carbon steel

Mechanical properties of wire arc additive manufactured carbon steel cylindrical component made by gas metal arc welding process

Microstructure and Mechanical Properties of High-Strength, Low-Alloy Steel Thin-Wall Fabricated with Wire and Arc Additive Manufacturing

Wire Arc Additive Manufactured Mild Steel and Austenitic Stainless Steel Components: Microstructure, Mechanical Properties and Residual Stresses

Cold Metal Transfer-Based Wire Arc Additively Manufactured Austenitic Stainless Steel/Inconel 625/Superduplex Stainless Steel Wall: Microstructural, Corrosion Properties, and Impact Toughness Evaluation

Experimental characteristics of 316L stainless steel thin wall processed in wire-based arc additive manufacturing process

Characterization of a low-alloy steel component produced with wire arc additive manufacturing process using metal-cored wire

Wire-arc additive manufacturing of AZ31 magnesium alloy fabricated by cold metal transfer heat source: Processing, microstructure, and mechanical behavior

Wire arc additive manufacturing using high-strength steel tubular and solid wires

Microstructure and Mechanical Properties of Weaving Wire and Arc Additive Manufactured AZ91 Magnesium Alloy Based on Cold Metal Transfer Technique

Development and Evaluation of Dissimilar Gas Tungsten Arc-Welded Joint of P92 Steel/Inconel 617 Alloy for Advanced Ultra-Supercritical Boiler Applications

Submerged arc additive manufacturing (SAAM) of low-carbon steel: Effect of in-situ intrinsic heat treatment (IHT) on microstructure and mechanical properties

Development of a New High Strength Alloy from Low Alloy Steel Wire by Innovative Additional Cold Wire Feeding Used in Wire Arc Additive Manufacturing

A review on wire arc additive manufacturing based on cold metal transfer

Boron addition to AISI A213/P91 steel: Preliminary investigation on microstructural evolution and microhardness at simulated heat‐affected zone