Abstract:In this paper, an improved rock mass characterization method is presented. This method used a quantified geological strength index (GSI) and synthetic rock mass (SRM) model based on a discrete fracture network (DFN) and bonded particle model. A quantitative method is initially introduced to assist in the use of the conventional GSI chart, employing the rock block volume as the quantitative factor. The block volume for a given DFN model is calculated by a volumetric joint count, which is defined as the number of fractures intersecting a cube with unit length. The peak strength and deformation modulus of the rock mass are estimated based on the derived GSI, and then selected as references to constrain mechanical parameters of joints in the SRM model. A parametric study shows a positive correlation between the joint stiffness/friction coefficient and both the peak strength and deformation modulus. The joint friction coefficients of 0.5, 1.0, and 1.5 are suggested to correspond to the surface quality of ‘FAIR’, ‘GOOD’, and ‘VERY GOOD’ in the GSI chart. An advantage of the SRM over the GSI lies in the characterization of the post-peak strain softening behavior. The numerical results show that lower joint stiffness and friction coefficient result in a more ductile post-peak behavior. Additional SRM models with varied joint distributions show the complexities of rock mass characterization, where the rock mass strength, modulus, and post-peak strain softening rate may vary significantly with only one aspect of distributions of the joints, such as intensity or diameter. Triaxial testing is also conducted, and the SRM peak strengths are compared with the Hoek–Brown strength criterion based on the GSI system. The strengths of the regular triaxial models show general convergence with the Hoek–Brown criterion, but the strengths of the true triaxial models are less than those of the regular triaxial models due to deviatoric confining stresses. Meanwhile, ductile post-peak behavior is generally simulated in the triaxial testing. Cracking models are finally investigated and presented, behaving as additional information to explain the changes in the rock mass strength and deformability with different confining stresses. The method presented in this paper is meant to help geologists and engineers to quantify the GSI for jointed rock mass, and characterize the rock mass modulus and strength. Meanwhile, the synthetic rock mass method provides an alternative for rock mass characterization in addition to the traditional GSI method.

A quantitative model for the geological strength index based on attribute mathematics and its application

An Improved Rock Mass Characterization Method Using a Quantified Geological Strength Index and Synthetic Rock Mass Model

Estimation of peak strength of jointed rock masses using GSI system

New Statistical Quantification Method for the Size Effect Behavior of Rock Mass Using Compressive Strength As an Example

A fully automatic-image-based approach to quantifying the geological strength index of underground rock mass

A New Perspective on the Constant Mi of the Hoek–Brown Failure Criterion and a New Model for Determining the Residual Strength of Rock

Numerical Method to Determine Mechanical Parameters of Engineering Design in Rock Masses

Development of a shear strength model for a rock mass containing a complex fracture system based on direct shear tests: a case study

Elastic perfect plastic rock mass analysis and equivalent GSI determination considering strain-softening behavior and three-dimensional strength

Estimating the geological strength index and disturbance factor in the Hoek–Brown criterion using the acoustic wave velocity in the rock mass

Explicit numerical models for the prediction of plastic and weakening rockmass behaviour around a circular tunnel in isotropic and anisotropic stress conditions

Quantification of the GSI and D values in the Hoek–Brown criterion using the rock quality designation (RQD) and discontinuity surface condition rating (SCR)

Comparisons of Evaluation Factors and Application Effects of the New [BQ]GSI System with International Rock Mass Classification Systems

A true triaxial strength criterion for rocks by gene expression programming

Spatial deformation prediction method of fractured rock tunnel based on quantified GSI and its application

An Elasto-Plastic Damage Model for Rocks Based on a New Nonlinear Strength Criterion

Multiscale Hierarchical Analysis of Rock Mass and Prediction of Its Mechanical and Hydraulic Properties

Evaluation of input geological parameters and tunnel strain for strain-softening rock mass based on GSI

Retrospective and prospective review of the generalized nonlinear strength theory for geomaterials

A new three-dimensional rock strength criterion based on shape function in deviatoric plane

Sensitivity analysis of GSI based mechanical characterization of rock mass