An integrated LSTM-AM and SPRT method for fault early detection of forced-oxidation system in wet flue gas desulfurization
Chunbo Pang,Dawei Duan,Zhiying Zhou,Shangbo Han,Longchao Yao,Chenghang Zheng,Jian Yang,Xiang Gao
DOI: https://doi.org/10.1016/j.psep.2022.01.062
IF: 7.8
2022-04-01
Process Safety and Environmental Protection
Abstract:Safe and efficient operation of the forced-oxidation system is of importance to the wet flue gas desulfurization (WFGD). However, equipment and system failures are commonly found due to the long-time running, frequent blower switching, and heavy workload etc., especially after the ultra-low emission (ULE) renovation to meet strict emission standard in China. This work develops a fault early detection method to improve the predictive maintenance of the forced-oxidation system including blowers, pipes, and the slurry tank. A model based on long short-term memory (LSTM) network and attention mechanism (AM) is constructed to predict real-time operation parameters and compare with the measured values. Then the sequence probability ratio test (SPRT) is utilized to analyze the prediction-measurement residual and provide automatic and dynamic warning. All the data for model training and prediction are from the build-in distributed control system (DCS) without additional sensors. The LSTM-AM model proves to accurately predict time-dependent and highly relevant parameters. SPRT can sensitively perceive the fault-caused residual deviation while alleviating the noises. Industrial application to the cases in a 50 MW combined heat and power generation plant is then carried out. Results show that the bearing failure of the oxidation blower and branch pipes (immersed in the slurry tank) blockage can be forecast in advance when the incipient degradation occurs.Deep learning is attracting widespread attention in the field of chemical process fault diagnosis recently. However, most deep learning methods are based on supervised learning and heavily rely on labeled data, with massive unlabeled data underutilized. Moreover, these supervised deep learning methods are uninterpretable and cannot facilitate fault localization, which is necessary for supervising the process back to normal. In this study, long short-term memory (LSTM) is used to extract temporal features and ladder autoencoder (LAE) is adopted for semi-supervised learning. Combining LSTM and LAE, LSTM-LAE is innovatively proposed to effectively utilize unlabeled data, with fault diagnosis performance largely improved. Moreover, LSTM-LAE achieves the interpretability to extract fault-relevant process variables with its elaborately designed internal features. When applied on a continuous stirred tank heater and the benchmark Tennessee Eastman process, LSTM-LAE exhibited a state-of-the-art fault diagnosis performance and localized faults to their relevant variables correctly.Leaking-burning coupling fires caused by oil leakage from tanks cause significant damage to occupants and the equipment. A series of experiments was conducted to investigate the fire behavior of a tank with oil leaking and burning. The tank released n-heptane into the tray below, forming a fire that heated the tank. The tray size and leak diameter varied. Spill fires, steady pool fires, boiling pool fires, and jet fires were observed. The results show that within a specific leak diameter range (2.5–3.5 mm), the maximum pressure increased with decreasing leak diameter. The fuel vapor spread along the bottom of the tank, causing the expansion of the flame. Consequently, the pool fire size was larger than the actual tray size, thereby making the maximum pressure and thermal radiation almost independent of tray size. When the leaking oil began to boil and burn, the pressure increased rapidly and the emitted radiative heat flux was the largest; therefore, fire posed the most serious threat. A computational fluid dynamics (CFD) modeling approach was employed to predict the time when the temperature of the leaking oil reached its boiling point. The predicted results were validated against the experimental ones, which provided useful support for emergency response plans.Patient satisfaction with healthcare was recognized as an indispensable component of healthcare quality assurance programs for decades. Limited research has explored psychosocial variables impacting patient satisfaction with cancer care. The objective of our study was to identify the level of patient satisfaction with cancer care in Riyadh, Saudi Arabia and determine the psychosocial and clinical predictors of patient satisfaction.A cross-sectional observational study was carried out in 2018–2019 with patients with cancer at the Outpatient Oncology Clinic at King Saud University Medical City in Riyadh, Saudi Arabia. The questionnaire contained a visual analog scale (VAS) of satisfaction with cancer care, a VAS of satisfaction with social support, the Patient Health Questionnaire-9 Depression scale, and the Generalized Anxiety Disorder 7-item scale.Out of the 400 patients approached, 280 agreed to participate in the study. Of the 280 patients participating in the study, 65% were satisfied with cancer care. Higher satisfaction was as -Abstract Truncated-
engineering, environmental, chemical