Abstract:INTRODUCTION: sensor setting. A Matlab (Mathworks Inc., MA) code was run to register The plantar metatarsal sites (i.e., five metatarsal heads (MTHs) and the two images according to three non-collinear ink dots marked on the underlying protective fat pads) at the ball of the forefoot are exposed hallux. "MTH template" represents the registered images with minimal to substantial dynamic contact forces during gait. Variations in vertical errors induced due to discrepancy between the target MTH and actual and shear components, including their magnitude and temporal sensor locations as evaluated by Xj and Yj. characteristics, may lead to painful conditions in rheumatoid arthritis and elevated risks of tissue damage in neuropathic foot [1, 2], Despite the fact that these clinical symptoms are often found at the forefoot and localized to metatarsal sites, there is very little evidence of accurate three-dimensional measurement of plantar metatarsal loads. One of the major obstacles is that pressure-shear sensor technology is still far from miniaturization to the point where it could accurately relate force distribution data to specific anatomical sites (e.g., the 2nd MTH) [3]. Gross plantar force pattern, for example, can only be "mapped" onto a specific portion of the foot (e.g., medial, central, and lateral forefoot) [4]. Subtle variations within individual metatarsal site often cannot be Figure 2. Method to create "MTH template" for the 2 MTH targeting. specifically extracted. This study describes the construction of a novel The subject initiated gait from a stationary posture. The right foot was gait platform-type system, and a pilot study to obtain the vertical, positioned over the gait plate with ankle being slightly dorsiflexed to anterior-posterior (AP), and medical-lateral (ML) ground reaction force simulate a heel strike. Data collections began as subjects started to (GRF) components of the foot plantar surface at individual MTH during plantarfiex to late stance and subsequently push-off, further completing barefoot walking. a series of 5 to 6 steps to the end of the 7m walkway at self-sleeted speed. To take measures at the each MTH, the "MTH template" was displayed on a laptop screen to guide the subject with appropriate starting point (i.e., heel-strike position) by direct comparison with the real-time image frames from the FASTCAM system. METHODS: Force sensor design: A customized tactile force sensor that is capable of detecting the forces at three orthogonal directions was specifically designed based on strain-gauge techniques. It has a flat top sensing surface that measures a square contact area of 1.9 X 1.9 cm. Each of the three sensor channels was independently calibrated by using an Instron machine (Model 5848, Canton, MA). Mechanical cross-talk was minimal (less than 0.1%). Measurement errors are less than 2.2%, 3.5%, and 3.7% for direct forces in the vertical, AP and ML axes, respectively.

Measurement of Slip Between the Shoe and Ground During Walking

A Novel Method for Evaluating the Effectiveness of Shoe-Tread Designs Relevant to Slip and Fall Accidents

Required Coefficient of Friction Versus Top-Piece/Outsole Hardness and Walking Speed: Significance of Correlations

Perceived floor slipperiness and floor roughness in a gait experiment.

Effect of Plantar Pressure on Stepping Friction under Cross‐slope Condition

Slip Risk Analysis for Trans-Femoral Amputees During Level Walking

Gait kinetics impact shoe tread wear rate

Friction Between Footwear And Floor Covered With Solid Particles Under Dry And Wet Conditions

Slip resistance of winter footwear on snow and ice measured using maximum achievable incline

Medio-lateral and lateral edge friction in indoor sports shoes

Evaluation of Different Pressure-Based Foot Contact Event Detection Algorithms across Different Slopes and Speeds

Efficacy of a rubber outsole with a hybrid surface pattern for preventing slips on icy surfaces

Experimental Study of Sliding Forces of Lander Footpad in Simulant Lunar Soil

The effect of wear on slip-resistance of winter footwear with composite outsoles: A pilot study

The Investigation on Semg of Lower Extremity when A Slip Occurs in Level Walking

A Novel Gait Platform for Simultaneous Measurement of Vertical and Shear Force at Local Metatarsal Site in Walking

The effect of roughness, floor polish, water, oil and ice on underfoot friction: current safety footwear solings are less slip resistant than microcellular polyurethane

A Walking Monitoring Shoe System For Simultaneous Plantar-Force Measurement And Gait-Phase Detection

A novel gait platform to measure isolated plantar metatarsal forces during walking.

Dynamic Walking on Slippery Surfaces: Demonstrating Stable Bipedal Gaits with Planned Ground Slippage