Abstract:Endovascular surgery through flow diverters and coils is increasingly used for the minimally invasive treatment of intracranial aneurysms. To study the effectiveness of these devices, in vitro tests are performed in which synthetic vascular phantoms are typically used to reproduce in vivo conditions. In this paper, we propose a manufacturing process to obtain compliant and transparent hollow vessel replicas to assess the mechanical behaviour of endovascular devices and perform flow measurements. The vessel models were obtained in three main steps. First, a mould was 3D-printed in a water-soluble material; two techniques, fusion deposition modelling and stereolithography, were compared for this purpose. Then, the mould was covered with a thin layer of silicone through spin–dip coating, and finally, when the silicone layer solidified, it was dissolved in a hot water bath. The final models were tested in terms of the quality of the final results, the mechanical properties of the silicone, thickness uniformity, and transparency properties. The proposed approach makes it possible to produce models of different sizes and complexity whose transparency and mechanical properties are suitable for in vitro experiments. Its applicability is demonstrated through idealised and patient-specific cases.

Correction: Bisighini et al. Fabrication of Compliant and Transparent Hollow Cerebral Vascular Phantoms for In Vitro Studies Using 3D Printing and Spin–Dip Coating. Materials 2023, 16, 166

Fabrication of Compliant and Transparent Hollow Cerebral Vascular Phantoms for In Vitro Studies Using 3D Printing and Spin–Dip Coating

Correction: 4D synchrotron microtomography and pore-network modelling for direct in situ capillary flow visualization in 3D printed microfluidic channels

A Brush-Spin-Coating Method For Fabricating In Vitro Patient-Specific Vascular Models By Coupling 3d-Printing (Dec, 10.1007/S13239-020-00504-9, 2020)

Erratum: Publisher's Note: "A suspended layer additive manufacturing approach to the bioprinting of tri-layered skin equivalents" [APL Bioeng. 5, 046103 (2021)]

Correction: Flax fibre reinforced alginate poloxamer hydrogel: assessment of mechanical and 4D printing potential

Correction: Improvement of Cytocompatibility of 3D-Printing Resins for Endothelial Cell Adhesion

Correction: Piezoelectric PVDF and its copolymers in biomedicine: innovations and applications

Corrigendum: Preparation and Characterization of 3D Porous Conductive Scaffolds with Magnetic Resonance Enhancement in Tissue Engineering (2019biomed. Mater.14 045013).

Corrigendum to "Tissue-engineered small-diameter vascular grafts containing novel copper-doped bioactive glass biomaterials to promote angiogenic activity and endothelial regeneration" [Mater. Today Bio 20 (2023): 100647]

Correction: Ultrahigh thermal conductive polymer composites by the 3D printing induced vertical alignment of carbon fiber

Fabrication of Soft Transparent Patient‐Specific Vascular Models with Stereolithographic 3D printing and Thiol‐Based Photopolymerizable Coatings

Correction to "Cellular Interaction of Bone Marrow Mesenchymal Stem Cells with Polymer and Hydrogel 3D Microscaffold Templates"

Correction: Thermoelectric Nanowires for Dense 3D Printed Architectures.

Piola et al. 3D Bioprinting of Gelatin–Xanthan Gum Composite Hydrogels for Growth of Human Skin Cells. Int. J. Mol. Sci. 2022, 23, 539

Corrigendum to ‘Fabrication of a bio-instructive scaffold conferred with a favorable microenvironment allowing for superior implant osseointegration and accelerated in situ vascularized bone regeneration via type H vessel formation’ [Bioactive Materials, Volume 9 (March 2022) Page 491–507]

Corrigendum to “3D-Printed Tri-Element-doped Hydroxyapatite/ Polycaprolactone Composite Scaffolds with Antibacterial Potential for Osteosarcoma Therapy and Bone Regeneration” [bioact. Mater. 31 (january 2024) 18–37]

Erratum: Corrigendum: Printing, folding and assembly methods for forming 3D mesostructures in advanced materials

Publisher Correction: Minimally Invasive Hemostatic Materials: Tackling a Dilemma of Fluidity and Adhesion by Photopolymerization in situ

Corrigendum: Three-Dimensional Cartilage Regeneration Using Engineered Cartilage Gel With a 3D-Printed Polycaprolactone Framework.

Correction: 3D Bioprinting Technologies for Hard Tissue and Organ Engineering. Materials 2016, 9, 802.