Abstract:In this study, we used a solution-casting technique to prepare all-solid-state composite polymer electrolytes (CPEs) based on poly(vinyl alcohol)/polyacrylonitrile blends, the ceramic filler Li14Al04Ti16(PO4)3 (LATP, NASICON-type structure), lithium bis(trifluoromethanesulfonyl)imide, and the solid plasticizer succinonitrile (SN) and then investigated their electrochemical stability, ionic transport properties, and interfacial behavior against lithium electrodes The CPEs prepared with optimal concentrations of LATP (20 wt %) and SN (10 wt %) exhibited a maximum ionic conductivity of 1.13 × 10–4 S cm–1 at 25 °C, a Li+-ion transference number of 0.507, and an electrochemical stability window of 5.1 V (vs Li/Li+). This CPE was a free-standing membrane and highly flexible. An all-solid-state Li//LiFePO4 battery assembled with this CPE displayed excellent cycling stability and rate performance at room temperature. A maximum discharge capacity of 159.6 mA h g–1 was achieved at 0.1C. The full cell achieved a discharge capacity of 119.4 mA h g–1 at 0.5C and a capacity retention of 90.5% after 100 cycles at ambient temperature. Therefore, this as-prepared CPE shows great promise for use in all-solid-state lithium-metal batteries.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsaem.0c02018?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsaem.0c02018</a>.SEM images of commercial 50050 LFP, particle size distribution and XRD spectrum of LFP, the SEM image of LATP, the EDX spectrum of the LATP powder, heating experiments, the flammability test, stress–strain curves, the i–t curve, AC spectra, the EIS Nyquist plot of the symmetric cell, SEM images of the lithium anode before and after cycling, and AC impedance of the battery (<a class="ext-link" href="/doi/suppl/10.1021/acsaem.0c02018/suppl_file/ae0c02018_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

A Highly Stable Long-Cycle Lithium–Oxygen Battery Based on Flexible PVDF-HFP@LATP Solid-State Electrolyte

Hybrid Crosslinked Solid Polymer Electrolyte via In‐Situ Solidification Enables High‐Performance Solid‐State Lithium Metal Batteries

Composite polymer electrolyte based on poly(vinylidene fluoride-hexafluoropropylene) (PVDF-HFP) for solid-state batteries

High voltage stable cycling of all-solid-state lithium metal batteries enabled by top-down direct fluorinated poly (ethylene oxide)-based electrolytes

Stable Cycling of All‐Solid‐State Lithium Metal Batteries Enabled by Salt Engineering of PEO‐based Polymer Electrolytes

Solid Polymer Electrolyte Reinforced with a Li1.3Al0.3Ti1.7(PO4)3-Coated Separator for All-Solid-State Lithium Batteries

Localized High Concentration Polymer Electrolyte Enabling Room Temperature Solid-State Lithium Metal Batteries with Stable LiF-rich Interphases

A High Ion Conductive Solid Electrolyte Film and Interface Stabilization Strategy for Solid-state Li-S Battery

In Situ Gelation of a 1,3-Dioxolane Dual-Permeable Porous Tandem Framework with Excellent Interfacial Stability to Power Long-Cycling Solid-State Lithium Metal Batteries

Long-Cycle Stability of In Situ Ultraviolet Curable Organic/Inorganic Composite Electrolyte for Solid-State Batteries

A Stretchable and Safe Polymer Electrolyte with a Protecting-Layer Strategy for Solid-State Lithium Metal Batteries

Boosting the Performance of Solid‐State Lithium Battery Based on Hybridizing Micron‐Sized LATP in a PEO/PVDF‐HFP Heterogeneous Polymer Matrix

Hydrogen-Bonded Organic Frameworks-based Electrolytes with Controllable Hydrogen Bonding Networks for Solid-State Lithium Batteries

Long‐cycling and High‐voltage Solid State Lithium Metal Batteries Enabled by Fluorinated and Crosslinked Polyether Electrolytes

Composite Polymer Electrolytes Based on PVA/PAN for All-Solid-State Lithium Metal Batteries Operated at Room Temperature

Hybrid solid electrolyte with the combination of LATP ceramic and PEO polymer by a solvent-free procedure

A newly designed composite gel polymer electrolyte based on poly(vinylidene fluoride-hexafluoropropylene) (PVDF-HFP) for enhanced solid-state lithium-sulfur batteries.

High Cycling Stability for Solid‐State Li Metal Batteries via Regulating Solvation Effect in Poly(Vinylidene Fluoride)‐Based Electrolytes

Modulating composite polymer electrolyte by lithium closo-borohydride achieves highly stable solid-state battery at 25°C

Layer-Structured Composite Solid-State Electrolyte with a Li 1.3 Al 0.3 Ti 1.7 (PO 4 ) 3 -Coated Separator for High-Voltage Lithium Metal Batteries by In Situ Polymerization

In-Situ Plasticized LLZTO-PVDF Composite Electrolytes for High-Performance Solid-State Lithium Metal Batteries